Search Engine

Arm Core

Add Question

174 Threads found on Arm Core
Don't know much but if you are targeting quad-core take a look here, Zynq UltraScale+ MPSoC Product Advantages: I think the quad application processor in the above is arm? Cortex™-A53 hard macro. But then you have mentioned Purpose is proof of concept
I am using DE1-SoC to start bare-metal programming for dual-core Cortex-A9 arm hard processor, Cyclone V. I'm trying to read data from SDRAM to FPGA using FPGA-to-HPS SDRAM Bridge. I configured FPGA-to-HPS SDRAM interface in qsys to use avalon-MM Read only, 32 width. I exported FPGA-to-HPS SDRAM Bridge avalon-MM Read only and write verilog s
The MYD-AM335X-J development board is a complete evaluation platform for TI AM335x (AM3352, AM3354, AM3356, AM3357,AM3358 and AM3359) arm Cortex-A8 Sitara Microprocessors (MPUs). It is designed based on the MCC-AM335X-J CPU module which integrates the core components on board including the AM335x processor, 256MB DDR3, 256MB Nand Flash, Gigabit Eth
pcDuino offers a arm Cortex-A7 Dual core, 4GB Flash and 1GB DRAM minimal development board, the pcDuino3C core Board, for $37 USD. JTAG lines are readily available through the breakout connectors and a 20-pin JTAG connector/cable should be easily fabricated. [ATTACH=CON
Based on guessing what you meant. You have been tasked with designing a Zynq design with the arm connected to a memory? If so just use the block design tool and add an arm and a memory, then use the auto connection feature to get those two parts to hook up. There will be a tab that allows you to modify the address map of the processor (changes t
Hello, I plan to establish communication to read write between two processors. On one side is a quad core arm cortex A9 processor on a ASIC (MCIMX6) and on the other side is a FPGA (ZC7020). I don't have any PCIe hard ports on the FPGA side. So there are two ways of establishing communication between these two processsors. If I intend to retain
the device is for a medical diagnostic Depending on the kind and amount of real time processing required, an approach based only on an arm core may be overloaded, leading it to the limit of its capacity.
Hi How to implement micro-controller for four different sensing micro-controller. For example, low power sensing one mode, high power sensing one mode,low power sensing two mode, high power sensing two mode, etc. how to get out of each mode, how to write the interrupt and handle those interrupt. Does anyone have experience on ho
1GHz and lower than 100$us??? and you don't like the raspberry pi? I think the new raspberry pi 2 with it's quad core arm SoC should be enough. + it's cheap, very cheap! 35$us + arm Cortex-A7 processor (32 bit) quad core at 900Mhz that you can overclock(careful there) has USB and ethernet (and SPi usart, and general io) you (...)
I'm looking for a specific file used for compiling the SIM900 core for use with embeddedAT (using the arm-none-eabi toolchain rather than RVCT). The file is called "", and would normally be found in the ..\EmbatSIM\comptool\gcc\lib\ directory (according to the app_make_inc_s file). Does anyone have this file? -R
One has a hard arm core, and the other doesnt but has more FPGA resources. The advantages come down to if you need an arm core or not...
Hello my Friends... :) I wanna to create a MP3 Player with arm - STM32F103RE and internal DAC. As you know this micro controller has 2 DAC that can produce sound in stereo mode in 72MHz core clock. So i choose it for my project. As i said, i choosed this mcu and i wrote a program for decoding MP3 (base on Helix codec and LPC1768 example code)
Firstly, the STM8S is not an arm core architecture, but a propriety 8-bit microcontroller core designed by ST. Secondly, to maximize the baud rate, TX/RX distance and decrease the susceptibility to RF noise, typically you will need to implement some method of encoding, like Manchester Encoding, when utilizing ASK/OOK RF modules like those (...)
From serial protocol candidates, SPI involves usually the lowest effort at the FPGA side. It's also the fastest protocol if supported by a hardware interface in the ?P, which is the case with arm. Makes SPI is the obvious way.
Hello All I have done many interactions with the PIC,AVR, and even 8051 MCU's Now i wish to work on arm and have done some hands on on LPC2148 also, But I wanted to know that which Series should i choose that has OS environment ?
Hello, I've designed a digital core with arm front end standard cell and an analog circuit in cadence Virtuoso in IBM 130nm. I wanted to do the mixed mode simulations in virtuoso. However, the arm front end standard cells doesn't provide any information inside. Could someone please help me in doing simulations with front end standard (...)
I have a STM32F405 and I need to toggle an I/O pin at 20MHz. Could anybody suggest how to do this? Would inline assembler be the answer? If so, how?
Hi Every one , Please help How to drive my C programming simulation into arm core and How to integrate the UVM testbench to arm SOC for functional simulation. I am using Questasim tool . Let know any reference documents, videos or any source to learn Very thanks in advance Balakrishna
hello guys i just got the following development board the altera DE1-SoC and was looking for good ebooks regarding programing this board and working with the dual core embedded arm processor i downloaded a couple of reading material and some eb
There are available interesting videos on the Web evidencing some successful experiments already performed on embedded platforms based on the same core processor arm Cortex-A8 used on Beaglebone board. As you asked, such projects employs OpenCV library to process captured video streams took from Webcam, but planned for achieve much more that c
Personal Computers employs a X86 core processor inside. If you compile a based arm processor, the executable code generated on compilation will not work if the VBox do not have the same core as the target for emulate. +++
Hello!! Everyone, I am new to Renesas Micro-Controller and don't know anything about it, except this that they use arm core in there product (have read somewhere this) I have to design a Schematic and PCB in CadSoft Eagle, which is based on Renesas Controller RX111 Group(R5F51115). This is controller name R5F51115, i am trying to search it
Hi I'm trying to build a simple code to run on a bare-metal arm micro-controller lpc1768 from NXP, that is from cortex-m3 family. I'm using Sourcery toolchain (specifically, Sourcery CodeBench Lite 2013.11-24 4.8.1) on Ubuntu 12.04, and I'm using the startup code found in lpc17xx CMSIS library, provided by NXP, in path /core/CM3/DeviceSupport/NXP
Review the arm datasheet, particularly the "shifts" paragraph the instruction set / data processing chapter.
Both boards are based on the most recent arm Cortex A8 core processor: Allwiner-A10. Concerning to memory bus, it is internal to the board, and there are already assembled with 2GB/4GB NAND flash. +++
Hi I'm trying to observe signals on waveform window in chipscope pro analyzer for viretex 7 FPGA on VC707 board. I get the message that "Waiting for core to be armed, slow or stopped clock". FYI, I've hooked up the design clock port *clk_BUFGP onto board ocsillator 200mhz SYSCLK_P pin at FPGA pin E19 . I have set the trigger port as the Reset sig
All variants of the NXP LPC21xx series of arm microcontroller share the same baseline features as they are all based on the arm7TDMI-S core, the major differences between these variants is an increase in Flash, RAM, GPIO and the addition of various peripheral hardware modules such as CAN, USB, ADC, Ethernet, etc. For example, the only (...)
For such applications involving massive data stream I presume you should employ cores able to handle external data memories, such as an arm based platform which seems best suitable. Note that referred camera exhibit a significant resolution. +++
First of all, you must know on what core is based the Arduino design ( arm, PIC, etc... ) and take the programmer tool, such as ULINK2, ICD2, etc... +++
Take a look at this site
Actually In my view first of all you need to try writing some Custom code on Hardware (preferably arm core like LPC2148 board ) like UART communication from PC, using internal ADC , keyboard interfacing .... then start integrating them in one application then you can use RTOS functionality to extend the codes .... refer this will help you - http
Nowadays, arm Cortex A8 fammilly becomes a good choice for some reasons, although be not essentially a DSP core. You can buy a Kit based on Allwinner A10 for U$ 49,00. +++
Do you have breadboarding supplies and benchtop power supply? There are many, many, many development kits of the AMR7TDMI based parts from several sources, including starter kits from IAR, Keil, Rowley Crossworks, and more. These kits are often more "turnkey" and come with what you need for hardware and pluf into a PC USB port with a cable, usua
iWave Systems Technologies recently introduced the iW-RainboW-G15M i.MX6 Q7 module. The new Qseven module features the Freescale 6 Series 1.2GHz arm Cortex A9 quad/dual/single core processor, on-board eMMC flash, Micro SD slot, expandable DDR3 memory, PCIe Gen2, Gigabit Ethernet, SATA 3.0, HDMI 1.4, SDXC and MIPI CSI/DSI. The Rainbow-G15M-Q7 i
Guys, What's the popular chip from Atmel wirh arm core and USB,SPI peripheral ? Thanks
Exactly, I noticed the last 3 development Kits I had purchased was exactly arm-based ( Cortex -M3 , arm11 , Cortex -A8 ). In the past, concerning to top line platforms, there was more variety in core options set ( MSP430, TMS320, etc... ) and currently it makes no sense spent some money or time developing at those hardware platforms.
uClinux runs as in a processor it is not directly implemented in the hardware. What it is implemented in the hardware is the processor for example arm with its RAM and ROM.
Use any arm Cortex microcontroller based board. Like M3 or M4 family. In my experience STM32F1xx series can be good choice. Try looking around what MCU has more tutorials to start with - will be easier to get in.
SBC210 is a EPIC size (Width x Height : 165mm x 115mm) single board computer. It is implemented with a SOM210 CPU module which is based on Samsung?s high-performance S5PV210 multi-media application processor. With the rich features that S5PV210 provided and the product-ready software packages, SBC210 enables developers to design embedded pro
arm and pentium's two channel can have 4 dram module? how much module can be extended? I try to make ram drive. so I think using current system is cheapest way. I search about arm core they have 2 channel ram ... Can I extend 2 channel to more than 4 ram module? and how about pentium? ( I mean i3-7 and xeon core ) (...)
You'll have to design an interface (usually through a FiFo) to communicate with your arm APB3 interface. Do you actually want to implement a C51 core with an APB3 interface? The SPI master needs to generate the clock signal for the SPI slaves. This SPI clock may be generated as a derivate of a system clock. One way (that I have implemented in the
Which arm do you really need? Sometimes it is better to use simple arm like arm7. It is really possible to have soft-core of arm7!!!
Hi Friends, I wish select a package what pinout is most avaliable and common to most manufacturers. Somebody could give some sugestion ? +++
you can treat it however you like - regular FPGA (with wasted arm cores) or one with an arm core in it. The benefit of hard cores is it will make data treansfer between arm and FPGA much easier and much faster.
Hi everybody... First of all, I'm so sorry if i posted this in a wrong place! Well, i posted it in a Portuguese EDABord version but had no reply so, I wanna know if it's possible to run MS-DOS (either 5 and 6.22 version) on a board with an arm or AVR core. 'There is no importance' if it's necessary to run over an VM, I just need 2 UART (one f
For what purpose? The Zync is an FPGA with an arm core in it, so you get the massive parrallel potential of writing custom logic or procesors inside the FPGA.
Try this, it will be a great deal of help. And about the core... Happy coding!
Hello, I backed this interesting project on Kickstarter : Parallella: A Supercomputer For Everyone. This project only has 25 hours left to reach its funding goal. You can help reach it funding goal by spreading the word, or even better, become a backer as
Hello all, Do you guys have any step-by-step tutorial how to create new project using IAR workbench? I have Freescale KwikStik board. Does the IAR workbench add arm core startup files automatically or I have to do it manually? If manually, then I am interested where to get the startup code. There are examples for Kinetis microcontrollers but I nee
There are too many overlapping criteria in many cases to give you a simple answer. The simpler PIC and AVR chips are quite similar in capabilities and often the choice is simply personal preference. Both are designed with more I/O control capabilities than actual processing power. PIC32 are newer though and have a 32 bit MIPS core that is much m