Search Engine

Basys 2

Add Question

Are you looking for?:
basys , basys board
19 Threads found on Basys 2
Hi! I have a basys 2 Spartan 3E-100 Cp132. I would like to use more pushbuttons in my panel (6 more). I would like to ask, if it is possible, to connect my additional pushbuttons to the expansion connectors (JA,JB,JC,JD). Any help would be greatly appreciated :smile:
Hi, I want to learn how to use communicate the FPGA with RS232, so I tried to create a project - whenever I hit the keystroke, the 8 bits LED will show the ASCII value. The hardware I used are basys 3 and Pmod RS232. I can successfully generate the bit file and load that to Digilent basys 3. However, it isn't implemented correct. Here are verilog c
Please try to keep it in the same thread. You now have 3 threads about the same topic of showing pretty pixels using your basys2 board. Also: coloroutput <= bar_rgb; I think I already explained how and why you should address ALL the 8 bits in such an assignment? So if your design doesn't work then you know why. You didn't listen t
That video timing is a bit off in the screenshot. There should be 13.8528 ms between your vsyncs, that is assuming you are running 800x600 @ 72 Hz. Check your clock too, it should be 50 MHz. basys2 has a 40 Mhz on-board clock, I believe, so that will require you to have a PLL.
Hi, I am getting an error while incorporating clock divider ( 40 MHz ) in VGA Controller ( basys 2 board ). I have also attached the snapshot of the error shown in my coding. Please help. 109898 The code is as follows : module anymodule(input wire clk,reset, output wire hsynch,vsynch, output red, output [2
Who can you please tell me how to order the basys 2 decimal point ?Please
Hello, This forum has been really helpful, I have gone really far into my project but I have two small little problems. Details about my project: I need to use SPI to connect two FPGA's (basys 2 SPARTAN 3e). Everything works except I have two problems: Here is a youtube video of my problem:
Hello, I want to my an LED pulse on for 1 second and off for 1 second with Digilent basys board using the 25MHz clock. Here is my code but it does not seem to output anything to the LED. The idea is to count however many cycles of the 25MHz clock it takes to make 1 second and then reset the counter and toggle the LED on. q_out controls the LED.
I did my Fisrt FPGA project, that is a free running 4 digit counter, Is working like a charm but I think is to much for to litle. Is my design ok, ? Have any way to optimize for less resource. I'm a newby on FPGA, but a experienced microprocessor programer, I'm afraid to use old stuff that is not the best for Fpga world. Please coment a
basys™2 Spartan-3E FPGA Board Xilinx Spartan 3E FPGA (100K or 250K gates) Intended for use with ISE or Webpack Digilent USB2 port providing board power, programming, and data transfers VGA & PS/2 connectors $49.00 for US student.
It's realy strange. With the .bit i uploaded, LD0 works fine in my basys2 board. Maybe the SW0 switch malfuncioning in your B2. That's a possibility. It may be fairly easy to find out, in the Adept 'Test' demo, the GUI screen should show the switch move up and down when toggled. If it doesn't show up on the te
I suggest you check the data sheet, page 4:
hello i have same problem with configure my ucf file to work with digilent basys board i just get the ucf file from digilent website : Digilent Inc. - Digital Design Engineer's Source but it doesn't work, i will be greatfull for any help It looks like it is not the ufc for thi
hi, I am trying to program my basys Digilent Spartan 3E-100 board using files generated by SDK. Which file should I download into the FPGA board? I tried download.bit using Digilent Adept software, but all it did was flagging the LED stating the FPGA has been programmed. Just want to know if I get the correct file.
Hi erenkcms, to configure the target device, in the case of basys FPGA Board, later of generate programming file (*.bit), you need use the digilent adept suite 2.1, you could use this manual or later install the software Adept go to Start -> Programs -> Digilent -> Adept -> Adept User's Manual I hope this help. Setzuna Fseiei
Hello, I need to create a basic ATM machine for a school project :D. I need to make it work on an FPGA device. I currently own a digilent basys board with the Spartan 3E chip. I tried using a FSM approach. I thought to make it work kind of this way: Each switch, if active will automatically, by convention, activate one of the bank ac
Could any one provide me the code for serial in parallel out. It has to have 6 bit out data. The serial in data i have to put it by my hand in binary code. The board is Xilinx Spartan 3E; chipset? XC3S100E; TQ144 basys (Basic System Board) Digilent Thank u library IEEE; use IEEE.STD_LOGIC_1164.ALL; use IEEE.STD_LOGIC_ARITH.ALL; use IEEE
Anyone know where i can find Verilog code for an LCD display controller. I am suing xilinx, and i have to test it using Xilinx's Spartan-3E FPGA thats on the basys board.
you can doanload at this : ( english page ) and register for demo at : 6 * F