38 Threads found on edaboard.com: Boost Converter Schematic
I design a boost converter which is good at operating with a fixed voltage source. However, once a voltage in series with resistor is used as a source. The input voltage of the converter is increasing. The converter has input capacitor which is ten times greater than the output one. It is supposed to have charging and (...)
Analog Circuit Design :: 02-23-2017 17:11 :: Wanoz :: Replies: 5 :: Views: 323
Hard to give any advice without a schematic. I assume you're using a synchronous boost converter? Are the FETs ever in saturation?
Power Electronics :: 07-08-2015 12:33 :: mtwieg :: Replies: 1 :: Views: 319
it is rated for 30V 3A but this is so small will it actually handle 90W?
Where do you see this rating? You are confusing boost converter output current with switch transistor peak current. About 30 W is the absolute limit with 12 V input voltage.
Power Electronics :: 03-05-2015 19:45 :: FvM :: Replies: 2 :: Views: 523
Please take a look at attached schematic and tell me if its going to work or not, If not what corrections are required.
its basically a boost converter with following specification
1. Input DC BUS IS : 5.8 - 9V
2. Output: 9V @ 3A
a> DC BUS: 5.8 - 9 V
b> 9V_SHUTDOWN: DISABLE SWITCHING OF UC3845
c> 9V_OUTPUT_OFF: (...)
Power Electronics :: 12-07-2014 12:07 :: nishu's :: Replies: 5 :: Views: 1768
I'm looking to boost a voltage of 3.6V to 9.5V with a maximum current out of 0 to 0.5A
for battery powered device.
Would like to fine an already built unit if anyone knows of one.
Or a working circuit schematic that someone done or knows of a circuit I can use
I done a search on Google. But? Wasn't able to fine what I needed.
Hobby Circuits and Small Projects Problems :: 08-29-2014 22:23 :: cybertron :: Replies: 11 :: Views: 1080
I have designed a boost converter LED driver with TPS40211. Vin 6 - 8,5 V (2 cell Lipo) and output voltage 10 - 75 V and current is 0,08 A almost 6 W. You can see schematic attached.
I have to change my design to 4 W constant power output. When the output voltage is increase, I want to decrease outpu
Power Electronics :: 05-15-2014 05:59 :: Knife :: Replies: 4 :: Views: 512
I'm trying to make a 12V to 320V DC-DC converter with TL494, and there is something weird going on.
50Khz frequency, 5+5:168 transformer (XF), no isolation, 50W expected power.
The problem is the diode D1 between the input and all the control circuitry.
With it, i'm getting over 20V af
Power Electronics :: 01-30-2014 19:49 :: Artlav :: Replies: 3 :: Views: 569
Please provide the complete schematic to understand the requirements.
It is look like a boost inductor with another (Auxiliary) winding for powering the Driver IC.
Power Electronics :: 01-28-2014 09:10 :: smijesh :: Replies: 18 :: Views: 1231
I think you're misusing the terms PFC and LLC, I don't see either in the schematic. I can't really see the operating principle of the circuit, especially M4. It looks like the "boost" stage is just going to send tons of ripple current into C2 and C3.
Power Electronics :: 01-15-2014 20:17 :: mtwieg :: Replies: 12 :: Views: 1142
I need boost converter for my project.
My spec is
Input Voltage = 6V to 10.5V
Output Voltage = 12 V
Output Current = 400 mA.
Frequency = 100 KHz
Here I attached my 99895 schematic model.
Power Electronics :: 12-16-2013 05:09 :: amayilsamy :: Replies: 2 :: Views: 929
Please find the attachment.
Can anyone tell what is the resistance value (R), so that the double boost converter will be in continuous conduction mode. Thanks in advance.
Power Electronics :: 12-09-2013 10:38 :: sasikumar :: Replies: 12 :: Views: 540
I have designed a soft switching flyback converter and simulated in MATLAB. But it is not working as closed loop.
It is not working in open loop especially boost mode.
What I meant by not working in open loop is that it doesn't give the required output for which duty ratio its designed.
In closed loop it doesn't give the reference v
Analog Circuit Design :: 06-21-2013 11:54 :: vidhz :: Replies: 2 :: Views: 688
Apart from circuit details - there are more dubious points - the exact behaviour of the boost converter part can be only guessed without a simulation.
For the time beeing I'll assume that it's working somehow. But how's the efficiency, does it use a reasonable operation point of the solar panel? How about in- and output voltages and currents wi
Power Electronics :: 04-26-2013 20:22 :: FvM :: Replies: 6 :: Views: 444
Maybe multiplying the output voltage using a coil, like in galvanic isolated designs?
Perhaps a boost converter is what you're thinking of?
This schematic illustrates the
Not shown is the co
Analog Circuit Design :: 03-19-2013 06:29 :: BradtheRad :: Replies: 1 :: Views: 664
A buck-boost converter can convert a positive supply to negative.
schematic showing the basic
You will need to add control circuitry.
The .5 ohm resistor is a 'token' value added to represent some amount of
ASIC Design Methodologies and Tools (Digital) :: 02-19-2013 08:35 :: BradtheRad :: Replies: 3 :: Views: 827
What helped me to grasp the principles of switched-coil converters was an animated, interactive simulator.
Below is a link to my conceptualization of a simple buck-boost.
Click it to open the website, load my schematic, and run it on your computer. (Click Allow to load the Java applet.)
Analog Circuit Design :: 12-15-2012 06:26 :: BradtheRad :: Replies: 1 :: Views: 772
No ZVS here ... need some triming i think... for zvs, your drain voltage have to be as low as possible. Resonance frequency of your LC must shape your drain voltage in a semi sinus waveform. just like here :
Professional Hardware and Electronics Design :: 11-21-2012 19:28 :: Gozaki :: Replies: 5 :: Views: 837
I am designing a Constant off time boost converter which regulates its own input current..........
Due to it regulating its own input current, does this mean it will be much easier to make stable?
Power Electronics :: 10-28-2012 11:59 :: treez :: Replies: 2 :: Views: 477
I would prefer to see your actual power circuit and driver circuit instead the data sheet diagram again and again.
It's true that IR2110 can't be used for an inverting boost converter, because it doesn't tolerate voltages below ground at Vs.
But I don't understand how the inverting boost schematic in post #11 is (...)
Power Electronics :: 10-31-2012 18:16 :: FvM :: Replies: 15 :: Views: 1263
The schematic ist correct, it's a pretty standard buck-boost converter. You'll need to implement a current controller that sets the PWM duty cycle to operate the converter with defined output current. Of course the controller must be fast enough to keep up with the dI/dt rate defined by the inductor.
Overcurrent shutdown (...)
Power Electronics :: 10-23-2012 15:20 :: FvM :: Replies: 12 :: Views: 1281
The odds of someone having a schematic and source code of a boost converter with some specifications you haven't even mentioned yet and using exactly the pic16f876A are extremely low.
Microcontrollers :: 08-19-2012 20:53 :: steinar96 :: Replies: 10 :: Views: 3548
Your schematic shows an inverting buck-boost converter topology, with wrong switch transistor polarity (N rather than P) and reversed diode, as said. A regular boost converter should serve your purpose
You are mentioning a NMOS transistor but placed a N-JFET in your schematic.
Power Electronics :: 08-09-2012 20:50 :: FvM :: Replies: 5 :: Views: 1459
The combination shown in the schematic can't work because the required input current of the second stage is a multiple of the current limited value of the first stage. The output load must be considerably reduced.
Yes, you are right!! I tried to make it work but there are too many issues to deal with!!
Is there a proble
Analog Circuit Design :: 07-07-2012 03:46 :: shawnmk123 :: Replies: 2 :: Views: 915
My project is DC-DC boost converter with PID Control.I build the circuit on ISIS, its working without PID control.Coz i didnt know how use PID control in order to getting desired output voltage.
Here is the circuit images and ISIS schematic file (.DSN)
Microcontrollers :: 04-17-2012 19:37 :: recon1729 :: Replies: 0 :: Views: 3008
Hello to everybody...i am new in this forum and i am italian,so, sorry for my english...
i need to project a boost converter in Proteus and control it with a atmega8535 using a pwm control.
My boost has a 5 volt input and need to have a 12 volt in output. In simulink if i use a square wave to regulate a switch with a
50000Hz and a value (...)
Elementary Electronic Questions :: 03-14-2012 08:25 :: fra84fra :: Replies: 7 :: Views: 2771
I have created 12Vdc using boost converter, and it will change its polarity as I direct H-bridge.
I have to have one visual and one audio feedback of correct volatage and polarity respectively.
I want to know what kinds of method i should use and what types of electronic parts i should use?
Power Electronics :: 02-13-2012 19:55 :: haydenlee87 :: Replies: 1 :: Views: 507
i am doing a project of boost converter using zero voltage switching (ZVS), the overall schematic shown in figure below. am using timer 555 to generate PWM to trigger the mosfet, the frequency about 600hz, Vin = 12v, Vo=47.5v, duty cycle = 58%, so my problem is how to calculate the resonant components (L2,C5) to achieve the soft switching. (...)
Software Problems, Hints and Reviews :: 02-01-2012 06:25 :: dark night :: Replies: 0 :: Views: 1170
where is your schematic? there are more arrangement of buck boost converter available .
Power Electronics :: 12-30-2011 17:50 :: goldsmith :: Replies: 7 :: Views: 1826
I am new here. I have some problem regarding the design of boost converter for my power design. I need to design the PV solar system, MPPT converter that act as boost converter to charge the battery from 50V system to 100V system. Anybody can help me in the design such as provide me the (...)
Elementary Electronic Questions :: 06-30-2011 18:36 :: asbat79 :: Replies: 4 :: Views: 2325
Can you provide a schematic because we can not guess what you're doing. Keep in mind that a boost converter (any fly-back like converter) needs some kind of soft start. The error amp will drive the switch to max. duty cycle at start-up because the output voltage is equal to V-in for a boost (...)
Power Electronics :: 03-03-2011 20:22 :: inventor(y) :: Replies: 5 :: Views: 1435
I have three commercially made 400watt portable strobes, all of which exhibit the same problem. They run on six NiCd cells (7.2v) and charge a photoflash capacitor to 360v. Normally it takes about 6-8 seconds to charge from 0v to 360v. However, at one point the output was shorted and part of the boost circuitry fried. The cap itself is OK.
Power Electronics :: 05-12-2010 18:17 :: AleXYZ :: Replies: 4 :: Views: 1079
Could you write some others details about the converter e.g. topology (Buck, boost, ...), feedback type (voltage mode, current mode, ...), functioning mode (CCM, DCM, ...), voltage on input/output and so on...
Do you've some circuit schematic?
Analog Circuit Design :: 04-29-2009 16:49 :: TekUT :: Replies: 4 :: Views: 1299
I'm on project with boost converter. I'm looking for schematic of model: FDC6305N, SI2306DS.
Anyone can help me?
Analog Circuit Design :: 07-13-2007 04:24 :: ngocthao :: Replies: 2 :: Views: 1357
I would like to construct and test a Switching Mode converter using MAX762.
But I do not know where the boost converters like MAXZ762 are used.
Can anybody suggest an application for it?
Is there any practical schematics for it showing MAX762 SMPS used for a certain application.
Analog Circuit Design :: 11-10-2006 00:33 :: Myauk :: Replies: 1 :: Views: 694
I'm looking to use an atmel attiny uC to make a simple yet efficient (85%) and SMALL buck/boost converter.
boost from around 1.8V and buck from 6-9V to drive a luxeon led. I need a schematic to get started and i'll figure out the writing of the code. Please help! Thanks!
Analog Circuit Design :: 07-08-2006 10:40 :: GoldServe :: Replies: 0 :: Views: 1774
recently, i have build a boost converter and when i start up the boost converter, more often than not, the power supply that supplies the boost converter overload. can anybody tell me why that happens and is there anyway i can prevent that from happening ? such as (...)
Analog Circuit Design :: 03-14-2006 17:49 :: mengghee :: Replies: 3 :: Views: 1082
Could you post you programmer schematic?
So I can how to do this boost converter.
Thanks you guys!
Elementary Electronic Questions :: 12-29-2005 15:10 :: cozturk :: Replies: 8 :: Views: 9668
I have attached a schematic diagram of my circuit and also a graph plotted on Duty Cycle Vs Vout. In the graph, it shows that when my duty cycle increases to 0.9, the output voltage is lower than the output voltage when the duty ratio is 0.8. how can that be possible ? so i thought i might have used the wrong component in pspice. but i can't find i
Analog Circuit Design :: 12-15-2005 01:54 :: mengghee :: Replies: 0 :: Views: 970