Search Engine www.edaboard.com

Carriage

Add Question

54 Threads found on edaboard.com: Carriage
When I send "AT", the LCD should display "OK" instead it displays "AT". Presume "AT" is the echo, but are you sending AT followed by carriage return.? The TXIF flag is taking a lot of time to get SET(0x01) after first two characters of sending data. TXIF will be asserted after the first character is send, takes s
Hi, I would like to send carriage Return (CR) instead of Line Feed (LF) in netact-1.11 for Windows 8. But I don't know how to do that? I read in some forum to use `r or -C but It didn't really help. Can anybody please help? Regards
hi, i am facing the problem while creating netlist was(value for property pcb footprint contains carriage return for c51 in cadence orcad capture tool.pls help me to get solution for that. Thank you in advance for support! Regards, Majed
you will have to send a string of 3 ascii char ie "999" to your MCU , probably with CR (carriage return or Enter) to valide and send it so your MCU will receive this string into a buffer your receiving routine must put zero into the buffer if detect CR car. ie : char buff; //if you send 999 ,buff will contain buff='9
An output line must be terminated with carriage return + linefeed. (0x13 + 0x10).
i found that sending "AT" as an AT command will give OK as a Result by the GSM Module Not exactly. AT must be followed by a carriage return character. inByte= Serial.read(); Serial.write(inByte); Why are you echoing incoming serial data back to serial output? Can cause endless ping-pong action. Please notice th
The ASCII char of a number is not the binary value and some values have other meanings like Escape, carriage return. does this help?
This is a message framing problem. Ideally the start and end of a message (one number) should be unequivocally detectable. In this simple case, you need a kind of separator between numbers. You're apparently assuming ASCII coded digits, so any non-numerical character can serve as a separator, e.g. space, carriage return, comma.
hi, i am facing the problem while creating netlist was(value for property pcb footprint contains carriage return for c51 in cadence orcad capture tool.pls help me to get solution for that.
Check whether you are adding " CR(carriage return)+ LF(Line Feed) " at the end of Every Command.
how to set carriage return in proteus virtual i type "AT" it show's "OK" loops then when i type AT again it will show ERROR:<0>
Post code. He is just testing gsm modem using a terminal program. There is no source code yet. @S.P.S. If you are testing the AT+CMGS command to send a text message, you should input the CNTL+Z character after you type the text message and not the 0x1A character or the carriage return or the l
First install an application "Tera-Term" or X-CTU or Hyperterminal Connect you GSM Module to PC Download datasheet of Sim900 "AT Command" there you can get all the list of AT Command But for simplicity first type "AT" follwed by carriage Return and Line feed , In the terminal just press enter after "AT" you will get OK as response Same way for
What part are you facing problem actually..? This much is what I figured out: You need to give carriage Return and Line Feed after every UART tx, not just carriage return. SBUF= "^Z"; The Ctrl+Z should not be a string, instead use the ASCII equivalent.
Assuming the motor is fixed and the carriage travels on the belt, it would be difficult to do that. It becomes more complicated when you have to restore the power as well as reverse it. Simply changing polarity with change-over switches is easy but the wiring gets much more complicated when you have on/off switches in line as well because the iner
Hi; I got a used HP Officejet 6110 printer. After switching it shows signs of life, but complains about the cartridges. When I wanted to watch them, I found that I can not open physically the carriage access door (also when turned on). Probably the unit is damaged, perhaps fell down (?), but otherwise it looks really good. From the manual:
Hello there! I had same problem, too a few time ago. After searching and doing some tests, I realized the following: Linux handles newline character '\n' as it should (i.e., it forces a newline), but Windows uses a '\n\r' newline+carriage return pair (don't know about the order, though) to force newline. However, if you use Wordpad to open your .t
'10' is the ASCII value for Line Feed. Linefeed means to advance downward to the next line. '13' is the ASCII value for carriage Return. carriage return means to return to the beginning of the current line without advancing downward. By first sending 10 and then 13, you are instructing: Move to next line downward. Move to the beginnin
I don't know that this is the cause but could it have to do with whether your command wrapper adds a carriage return & line feed at the end of the string? Or just a carriage return?
hello eveyone, I'm trying to make a simulation of SD card with ISIS Proteus , the code for the Microcontrolleur is in C langage! but I don't know why i don't get something in the virtual terminal !!! help mee pleaaazz!!! here is the code: // This function sends carriage-return and line-feed to USART // sfr sbit Mmc_Chip_Select at R
hello, I i get a good understanding, your PIC send AT+CMGR=1 + carriage return by TX of the UART and you are waiting the response ( as described in post#1) on RX of the UART. Where did you init the buffer "a" ? you must reserve some place to contains all the caracteres et point at the begining of the table ex char text;
One issue maybe that ASCII 10 or 0x0A is actually a LineFeed (LF) or NewLine (NL), while a carriage Return CR is 13 or 0x0D. Depending on your terminal emulation program, the PIC may or may not ever receive the LF or NL. Are you sure the carriage Return is indeed being detected? And the data actually being written to the SD Card? You may w
A couple of things: You need to make sure that your serial-reading loop terminates before the ReceivedMsg variable overflows, and you have not initialised MsgChar - either initialise it before entering the while loop, or use a do...while loop instead. I fail to see why gets() won't work, provided your string has a carriage return. How are you
Hi folks, I am using a Sim900 and currently I'm trying to transfer JPEG-Pictures with the on-board FTP-client. Everything works fine, but when I transfer the data in 512byte blocks with the command "AT+FTPPUT=2,512", the Sim900 modifys my binary data. Everytime there is a 0x0A (Linefeed) in the data stream, it adds a 0x0D (carriage Return) befor
Without seeing the program it's difficult to guess, they are just numbers stored in a table. They could possibly be the Ascii characters for Line feed (0A) and carriage return (0D) which you often find at the end of a string of characters. Brian.
Which terminal software are you using?a carriage return and linefeed should be at the end of each at command therefore append carriage return(CR) and append linefeed (LF)should be enabled.Some gsm modem works even if there is no linefeed but carriage return is must after each at command.check other parameters like COM Number ,baud rate etc (...)
Hi friend, GSM module send OK responce of AT command with carriage return(0x0D) and Line Feed(0x0A) value before and after of responce like "\n\rOK\r\n" Check Is your lcd garbage data 0x0D or 0x0A? Read Data sheet of GSM module carefully. Best of Luck
The BASIC language has a keyword named INPUT. I fear, the question is very unclear. It's actually asking how to send a specific string to the COM port. "" is somewhat misleading, because it obviously means carriage return, or a carriage return/linefeed combination.
many modems require a carriage return character \r as well as \n, try send2gsm("+++\r\n"); however, reading the SIM300 manual it states To prevent the +++ escape sequence from being misinterpreted as data, it should comply to following sequence
You are using GPRS ... instead of sending character by character write a function that sends String... and i hope you have to add carriage return and line feed and end of each AT commands
The response of the AT+CGMR command will be a header containing some information about the message such as; the sending number, the date and the time. Then, a carriage return and a Line feed. So, as nandhu015 said, you can start reading after the 2nd carriage Return and Line Feed. The ASCII characters of the carriage Return and Line Feed are (...)
I see your program is like this sr_str("ATD9970706080") 1. the syntax is ATD+91xxxxxxxxxx; there is no +91 nor semicolon at the end of number in your code. 2. its carriage return + line feed (0x0a) + (0x0d) ......... you have one command only 3. you are putting entire thing in a while loop... it will execute the 3 lines in micro se
Not sure if it will solve your problems, but I wanted to point out that the line terminator should be CRLF (carriage return=0x0D then line feed=0x0A) and is encoded as "\r\n" and not the other way around! Arthur
Hi friends recently i have seen a video in you tube , a robot following a man. this is the link YouTube - Autonomous Car - Autonomous carriage Transporter I just want to know the technology behind it ...pls share information about it if u have any idea. thanks
Hey, Here are some of my projects that I've done: YouTube - Autonomous Car - Autonomous carriage Transporter Hi, it looks quite interesting. can you share this project with me. component list, ckt and code
You haven't picked an easy model to use - it is weird! It works on my simulator but I think the problem may be to do with nested subcircuits. Try moving the following line in the model file .ENDS OPA2674_Model to the bottom of the file (and add a carriage return as they couldn't be bothered to include one!). See the notes at the heade
Try addding a "carriage Return" after the command.
You need to add a carriage Return to the end of each command you send. Also, those long delays may cause problems with some modems - you shouldn't need any delays!
1 - Is your hardware configured correctly - TX of uP to RX of Modem, RX of uP to TX of modem? 2 - Are you sure your sending commands to the GSM modem -Serial port configured, proper handshaking, proper baud rate, etc. 3 - Are you terminating the "AT" command with a 'carriage return' when you send commands via the micro.
just send "AT" via UART to Mobile,it will reply u "OK" if everything is ok.. MikroC might be having in-built function to send string via UART.. for example if the function available is something like printf() then printf("AT\r\n"); //make sure carriage return is used.. it will reply "OK"... use some functions to get th
Hi, The syntax looks correct to me in your original code and I see no reason to do the changes suggested above. I believe it could be something compilator-specific, such as unseen/unprintable extra characters in the source, or the macro-definitions (e.g. carriage return not followed by new line; make sure you write the source in a compatible edito
The module communicates to your microcontroller using an asynchronous serial communications channel (UART). You just need to connect the SIM508's TX line to your controllers RX line, and the 508's RX line to your controller's TX line. Commands are sent as stinrgs that start with "AT" and end with a carriage return. You'll need to refer to th
void uart_gets(char *s) // Get String from UART { while(((*s)=uart_getc())!=13)s++;//until last character is carriage return *s=0; } enjoy!
anyone know how do i interface the PIC with the hyper terminal using RS 232? what are the syntax for it or where can i get them? thanks... also, how do i tell the PIC to place an "enter/carriage return" key? Search the board, this had been discussed many times already.
most of the GSM modem needs a carriage return after the message.... this terminates the message and only then the gsm modem sends the message.. make sure with this and then check... also check the AT command for ur A1018
What's your desired precision for the position measurement? How long is the rod? Optical strip is a good idea. If the carriage uses rack and pinion with teeth to move along the rails, you can add a rotary encoder to the motor. If you have a frictional rack and pinion, I would add a separate non-driven wheel with a rotary encoder for position
hi, I dont know how C works but it seems that at: unsigned char ATEO = "ATEO"; unsigned char Delete = "AT+CMGD=1"; //Deleteing SMS in index 1 and after the AT+CMGD=1 you need to send a CR (carriage Return) instruction to the phone. Also make sure you can read data from phone, maybe there is a connection problem, hardware
CCS compiler includes the carriage return and line feed as per the manual: PUTS: Sends each character in the string out the RS232 pin using PUTC(). After the string is sent a RETURN (13) and LINE-FEED (10) are sent. In general printf() is more useful than puts(). Ric
You need to be able to read/write to the comport(RS232) of a computer from VB6. There are lots of components and sample codes around the net. After you are able to use the serial port from VB6 all you have to do is to send the command string to the modem with a carriage return at the end. as example; AT
i've managed to include a carriage return character after each block of 8 bytes i also set the buffer length at 8 bytes in the p16_tprp.asm So you send 9 bytes (8 + ). Now look at this statement in your code : ErrRxBufOver: decf RxByteCount,F ;decrement byte count to overwrite last received g


Last searching phrases:

seven | seven | seven | seven | seven | forth | forth | three five | near far | last three