Search Engine

105 Threads found on Gprs Code
Hi Guys, I have an arduino UNO and have some sensors, I have made a database in mysql, how can I send the data from sensors to the table's columns of thedatabase via GRPS connexion of M95 quectel? any code exemples will be appreciate very much!
hi how get sim card balance by gsm/gprs A6 module? I used the following AT, but does not work and result in unreadable characters or numeric code. note : my sim card language is English. I used all four AT+CSCS that is supported by A6.but I can not get +CUSD: "English-message". why? AT commands: AT+CMGF=1 AND/OR 0 AT+C
Hi, What code do you need? gprs modules often communicate via UART, but it could be any other interface, too. code for sending and receiving data with a UART? Or do you need to know the gprs commands? How do you want to process the gprs data? Storing in memory, showing on a display, transmitting to a PC? (...)
hey we have an ongoing project and that need to have an important application that is firmware upgrade over the air. we are using Atmega 128 which having two UARTS. two options to get connected with internet are (RN171)WiFi and SIM900A(gprs). i saw a website on which the user upgrade the Arduino firmware using ESP8266(Wifi module). [U
I am using arduino uno with itead 3G shield , my shield works fine but it doesn't responding properly , After sendint "AT+chttpact =......" it back me +CHTTPACT: REQUEST then when it send GET command it doesn't response at all What could be the problem ?? here the real response and the code : GSM : Registered to netwo
i have problem with sim908 when i try to connect by gprs and also try to use gps, sim908 will reconnect and gps willbe off i use someat to power on gps inside my code but it will reset the module and it doesnt work please help me tnx
SIM900 command runs without any problems on a network with apn, a number of directives not implemented on SIM900 and it is impossible to connect to the network. Of course, if a sim900 previous code was not performed previously on the new rules apply at work without any problems. Because of the large number sim900 I use so I can not change all of ou
Hi guys, I have setup a TCPIP connection between my ITEAD SIM908 development board and a server on my PC(SocketTest v3) using the following code: AT+CIPSHUT AT+CIPMUX=0 AT+CIPSTATUS AT+CSTT="internet","","" AT+CIPSTATUS AT+CIICR AT+CIPSTATUS AT+CIFSR AT+CIPSTATUS AT+CIPSTART="TCP","","
Hi all, I am using HTTP GET method to transfer few bytes of data to a web page, Now it takes 10-12sec for the modem to transfer data to webpage. Is it possible to upload data within 1-2sec ?, so that i could send more samples to webpage. The commands which i am using: // for initializing AT+SAPBR=3,1,"Contype", "gprs" AT+SAPBR
I have an Arduino in a remote location and would like to upload new code via gprs (a SIM900 is connected to the Arduino via TX/RX serial interface with hardware handshaking (DTR, CTS, RTS connected)). I was thinking about putting the .hex file (or some format) on a webserver and Arduino will automatically check once a day if there is a new sketch a
How can I reset SIM900 ? I am making a library for SIM900 GSM/gprs communication. I want to implement reset function in the code. One function will be to send AT Commands. I need to implement reset function inside this function. It sends AT Commands 3 times to SIM900 and if SIM900 responds with ERROR or if it doesn't respond for 3 times then the
Hello to all! I am working with SIM900. It works good but when i want to send data with gprs "AT+CIPSEND" , it crash. Please help me.
I am setting up a connection. >"at^scfg=tcp/withurcs,off ok >"at^sics=0,conType,gprs0 ok >"at^sics=0,apn, ok AT^SICS=0,user,mts ok AT^SICS=0,passwd,mts ok >"at^sics=0,dns1, ok Configuring SMTP Service Profile at^siss=9,srvType,"Smtp" OK at^siss=9,alphabet,"1" OK at^siss=9,conI
never attempted FTP using a SIM908 but have a look at there appears to be code for connecting to FTP using a SIM908 it may give you some ideas
I use SIM900D module and interface it use software. I write that software code use VB 6.0. But I face a problem. If a incoming call in my gprs module that time my module send ?RING? string. I see it a text box. But I want to do that when my RS232 receive ?RING? that time does something like as Beep. My software work normally but when my module send
The first thing to do is to know the gprs module and its management commands, you already did that? Then u need to choose a microcontroller to manage the gprs module and then choose a language to the development of the code. Do you know any? Have an idea in mind about what to use microcontroller (I usually use PIC). Please answer these (...)
SMSsending("AT+CREG?\r\n"); delay_ms(450); linefeeder(10); delay_ms(250); delay_ms(250); delay_ms(250); delay_ms(250); SMSsending("AT+SAPBR=4,1"); delay_ms(450); linefeeder(10); delay_ms(250); delay_ms(250); delay_ms(250); delay_ms(250); SMSsending("AT+SAPBR=3,1,\"CONTYPE\",\"gprs\"\r\n"); delay_ms(450);
hi every one My Objective: i am trying to test my new GSM and gprs modem that i brought from local electronics market. And i want check the functionality like sending and receiving SMS,CALLING,gprs functionlity etc.. for this i am trying to test this modem using AT commands... these are the results that i am getting RDY +CFUN:
This is my story.... from power off then on, RS232 19200 boud rate, Italy Wind operator NORMAL POWER DOWN AT+CREG? +CREG: 0,1 OK AT+CGATT? +CGATT: 1 OK AT+SAPBR=3,1,"CONTYPE","gprs" //pag6 SIM900_IP_Application Note_V1.04 OK AT+SAPBR=3,1,"APN","internet.wind" OK AT+SAPBR=1,1 OK ************** here stop resp
I'm trying to identify and locate what appears to be a WeBee GSM/gprs development board. It has an onboard microcontroller, 16-button pad, LCD port, I/O ports, relay, and misc. other push switches. It looks like a handy fixture. This link displays the board in
iam using AT91SAM7A3 microcontroller ,i want to communicate with ublox GSM/gprs modem using gprs ,in LEON g100 we have at commands please send me gprs code for how to send at commands from Microcontroller to MOdem THANKS®ARDS K.Chandu
I think that 100% sending data at 1s isn't possible over gprs and not over HSDPA ...... Yes speed is high but not allways! You must search for AT commands in user manual for permenently gprs connection! If you attach code maybe someone can help you!
Unfortunately, I am not familiar enough with BASCOM or any other variant of Embedded BASIC to be of much help in composing the required code. However, I would suggest attaching your GSM/gprs module to your PC's serial port and using a terminal emulation software like Putty to test and troubleshoot the required AT Command sequences. Once y
Help!! Does anyone can write concept of programming on sending sms on gprs modem connect with at89c51??? Kindly give me some ideas>
Hello friends.. I have learn sim900 module connect the gprs mode and get the HTTP data for any site or we can say url.. so i try this below code in keil,But the apn was not set,so got he error,, so how to solve ...ples Tell me.. int main (void) { unsigned char t=1,z; // int j; IO0DIR = 0xFFFFFFFF; init_lcd(); uart0_in
Hi there, Please go through these links and revert me back.
can u tell from which site details to access internet from the GSM.......... i know the AT commands sequence to be followed to acquire gprs connection.. but i m not getting how to implement those in c can u help me?
Hello , I am using two Sim 300 MODEMs for server client application.I am able to communicate in non-transparent mode, but i can not communicate in transparent mode. My Client code >>AT+CIPMODE=1 <>AT+CGATT=1 <>AT+CSTT="www" <>AT+CGDCONT=1,"IP","www" <>AT+CDNSORIP=0 <>AT+CIICR <>
Hello evryone!! I use a module gprs (wismo228) to tranmit data. This module is on serie with pic24. I want to send AT commande and Data at the same time. This fonctionality is only possible by using the CMUX fonction. But i don't know how to implemant this cmux fonction in the pic. Does anyone can help me for that? Thank
First of all, good day to all. My goal is to POST variables to my webserver usign gprs modem SIM900. For testing purposes, SIM900 modem is connected to PC via serial port with a MAX232 in between, running 19200,8,N,1. No Flow control. My webserver: Apache with PHP 5. Software used: Hyperterminal, Tera Term and other terminal emu
I've got a SIM300 gprs Module . And I want to make an HTTP Request to a PHP file with my gprs Module. This is the code of my AT Commands : { if(firstTimeInLoop){ gprs.write("AT+CGATT=1"); gprs.write("\n\r"); (...)
hello : ) my project is to make my gprs modem sim900 communicate with a distant web server using tcp mode. i made the sending data code successfully. concerning the data receiviing i don't know so much how to proceed : i have just to wait for a response in a while condition just like : while(strcmp (buffer, " "); // wait until buffer is full bu
hi everybody,, i am using below commands to send and receive sms using sim900 gprs modem.. but i can able to send messages from hyperterminal.. but if i send message from my phone to MOdem i am unable to see those messages.. so pls help me to get out from this problem...: :roll: :roll: :roll: :roll: :roll: :roll: AT+CMGF=1 OK AT+CMGS="+91xx
You code is totally wrong. I think you need serial receive code right? Do you have to issue any commands to gprs system? A sample program to receive data. It doesn't display the result. How do you want to display the result? On LCD? #include #include #define FREQ 11.0592 MHZ void USART_Init(); void U
Hello!! I successfully transmit data to a TCP server using SIM300 Module using Windows Hyper terminal. But i have to automate this process. But not able to write code for it, don't know why i am not able to receive data from gprs Module properly. I am using PIC18F8722 Micro-controller and whenever i tries to receive data it Serial Port Over
How to develop a C code using AT commands for transferring the data between gprs modem and Remote server by setting up a TCP connection to the webserver.............The gprs modem is interfaced with an ATMEGA 16A microcontroller...................Please help...............
hi I am trying to download and upload a file to an FTP server. i m using FileZilla server. I have done these steps. All queries are working well. what are the errors? AT OK AT+CGATT=1 OK AT+CGDCONT=1,"IP","UFONEgprs" OK OK AT+SAPBR=3,1,"Contype","gprs"
Haiiiiiii All, I am new to this technology. Please help me for how to write a code to a SIM300 gprs Modem to send the data into a html page. I am using ARM7 LPC2148 Microcontroller to control the system. The data of the system has to update into a html page. Please help me. Thanks in Advance.
Haiiiiiiiiiii Good Morning one and all, I want to know how to write the interfacing code for SIM300 gprs Module with ARM7LPC2148 Microcontroller. I want to update the status of the devices(light,fan and DC Motor) in my project to an html page. I didn't have any idea on this, but i want to implement this. Please help me. Thanks in Advance.
I am using SIM300 GSM/gprs Module. But i am not able to send sms from this dont know why. The commands i am typing from Hyperterminal is as follow:- AT+CMGF=1 OK AT+CMGW="9650126047" > Hello!! this is Arun Sharma > (here i Press Control and Z Button +CMGW: 1 OK AT+CMGL="ALL" +CMGL: 1,"STO UNSENT","96501260
Hi everybody I wanna connect to FTP Server via SIM300 gprs. I am sure about my command sequence, but sometimes it works and sometimes it doesn't work! Do you know what is the reason? AT&F OK AT+CMEE=2 OK AT+CIPMODE=1 OK AT+CGATT=1 OK AT+CGDCONT=1,"IP","mtnirancell" OK AT+CSTT="mtnirancell",,OK AT+CIICR AT+CIFSR
Hi friends I have a problem in communication with FTP server via SIM300 gprs when I connect to a HTTP server such as, I can send my TCP commands like this: AT+CIPSTART="TCP","","80" OK CONNECT OK AT+CIPSEND > GET / HTTP/1.1 Host: Connection: Keep-Alive Accept:
Hi everybody I wanna download files from FTP server via SIM300 gprs I can successfully connect to server, but then, I can't execute FTP commands here is a log of my connection: AT+CGATT=1 OK AT+CGDCONT=1,"IP","mcinet" OK AT+CSTT="mcinet",, OK AT+CIICR OK AT+CIFSR AT+CIPSTATUS
atd*152# OK +CUSD: 0,"Your account balance is TK. 12.65.Your account will expire on 29/12/2012.",64 at+cgdcont=? at +CGDCONT: (1-3),"IP",,,(0),(0) OK AT+CGDCONT=1,"IP","wap" OK atd*99***1# CONNECT NO CARRIER AT+CIPstart="TCP","","80"
Hi , I am doing my project with gsm/gprs modem . We are sending some data through the modem to a website which was created by us . I am new to this modem . So please any one help me to work with that. please send me the AT Commands for the data transmission using gprs.
Hello everyone. I am trying to access the web page through gprs sim 900 modem. at+cipstart="tcp","","80" OK CONNECT OK at+cipsend  GET /HTTP/1.1 SEND OK After these commands what can i do. I am really very weak in networking. please help me out.
Hi everbody. I working on send data to my php codes for a several day. I using cinterion mc52it gprs modem. I was look this thread : I can connect to my web site. But i cant send data to php codes. Which method should I choose for send data(polling? urcs?) And there is my codes: public void Wri
hi everyone, can u help me in writing arduino uno code for data send to web server using gprs & receive command from web server & take action, please reply me as early as possible thanks
hi everybody, how i can send cellid, lac, mmc, mnc data to through gprs. thanks
Hi! I am working with PIC18F26J50 and gprs/gsm module sim900 and right now im having a strange problem. Right now, we are sending from the pic to the sim900 an 'A' to configure the autobauding (8,N,1) and the sim 900 is responding correct the same letter A. After that, we are sending AT CR LF (with the correct ascci number or hex) and we did