Search Engine

Proteus 7 Segment

Add Question

39 Threads found on Proteus 7 Segment
Are you want to use a counter...??? then what is the use of RB7 in program and circuit. Also your code seems to be good, but what about the configuration bits you used...??? In proteus have you set the configuration bits correctly? Your program on startup will continue to increment. so introduce some more delay (in ms) to see the display update.
Animated Simulation are not possible on OrCAD. Use proteus for simulation and OrCAD or Schematic and PCB design.
Don't know what the "segment delay" value actually is, but there should be no problem to run the code in real hardware without flicker. In case you are talking about flickering in the proteus simulation, I suspect a pure simulation problem. Adjust the timeout in the LED display properties.
Hi, I am very new to proteus and would much appreciate a little help. I have made a schematic in which to count with 2 seven segment displays. I thinkit is all working as I can see the red/blue switching colours. But the displays remain dark. I think I have them powered but nothing. They are common cathode. Any advice would be gratefully wel
If you show your schematic in PNG format, you'll probably get some help. Not everyone has proteus 8 and many dont use proteus at all. As for me, I am still using ver 7.8 SP2. Allen
Sir, I m very new using c compiler as mikro-c pro v6.0.1. Please help me with c-code for 7 segment clock using PIC 16F887A & DS1307. My proteus file as follows. 105919
I doubt that there will ever be a model for this chip in proteus.What I do when I want to simulate a processor driving a complicated chip like the vs1003 is to make the input circuit and registers of the chip using normal logic with BCD seven segment displays to display the contents of the registers. This is good enough to enable you to debug your
Post circuit in proteus 7.x format or image file. Is it Charliplexing or Multiplexing?
can any one please help me to make MicroC Pro for Pic code for the attached schematic. the 4SSDs to display 4digit numbers set by the 3Buttons Thanks Madayan - - - Updated - - - 97811 MPLXING SSDs[/QU
Hello there,I would like to make a counter counting from 00-99 and then go to start (go to 0),the added push button when pressed it reset the PIC;I am using ccs c compiler. can you please help,here are the complete project,proteus simulation and the codes I tried to run;it is working but jumping some digits (0,6,8 and 9). See the codes below,
Hello there,can some body help me to know where the error is I am design a 0-30V digital voltmeter but I am always getting 0V on the seven segment display. Here are the code and the proteus circuit. #include "16f876a.h" #DEVICE ADC=10 #fuses XT,NOWDT,NOLVP,NODEBUG,NOCPD #use delay(clock=4M) #include
sir ...i am trying to make a digital clock using 4 common anode 7seg dispaly....i hav found the code in net ..and it seemed alright also but when i simulate it in proteus taking 4 individual common anode 7seg it didnt display anything..after that i connected a 4 digit 7seg display it showed the result but with too much flickering please help me wit
I have my code and already implemented on hardware that scan 4x4 matrix keypad and display a number in seven segment display, now I wan't to connect a DC motor so that number 1 is pressed on keyboard motor should rotate clockwise and when 2 is pressed motor rotate ant clockwise., the code for keypad and proteus simulation are down here, kindly
Dear All My attached picture for PIC 16f877a seven segment display clock using timer1 external clock Oscillator mode is enable correctly and my actual hardware is working but proteus does not working Please advice, Am I connected correctly watch Crystal to T1OS0 and T1OS1 pins when I select the internal clock source then it is working pro
I want to know the pin no. of 16 segment display module which is shown here (proteus). If somebody could name the pins it will be
This is not a bug, just the simulator "overload" indicates. My proposal (only in proteus :wink: ): - abandon the four emitter-follower drivers - abandon the entire oscillator and reset circuit If that does not enough, use the 7SEG-MPX4-CA device, instead of the separate 7seg displays.
I am trying to simulate this BCD to 7 segment with Leading zero suppression circuit in Multisim 12. But do not get output. Same circuit simulated in proteus 7 gives expected result. Where I am wrong. 88237 88238
hello, i am using seven segment display for making digital clock. i have made a program for this but on the time of simulating on proteus, it does not gives output & its also does not display even a single seven display. when i start simulation it gives an error." SIMULATION IS NOT RUNNING IN REAL TIME DUE TO EXCESSIVE CPU LOAD" now i am u
What you refer to seems to be the name of a simulation model of proteus, if so there is no datasheet, this is a virtual device.
Hello, i m trying to build one counter circuit with 4 7-segment multiplexing... my program is correct but still not properly working with proteus guyz.. i need to calculate how to calculate refresh rate "Minimum Trigger" setting in 7 segment display properties....should i keep it default or some calculation is required ? i ha
How to add seven segment led in proteus?
hi all I have written the code blew in mikroBasic Pro to drive 4 seven segment & it works well on proteus the purpose of code is to make a counter from 0 to 9 on the 4 seven segment but when i apply it on the real world it does not give me the expected result also the seven segment are flickering all the time note : (...)
help using 7 segment display in proteus how to configure the package of common cathode.
hi every one.. i'm facing some problem in my projects. i worked it on proteus and i have attached some snaps shot of my project. i'm reading analog i/p from RA2 and display it on 4 7-segments devices. i used 74ls78 bcd to 7 segment decoder and 74ls138 decoder. i've copied my source code too with this. the fig1 shows the intial setup and (...)
I would like to simulate a thermometer wich uses seven segment for displaying ;I want to use CCS C compiler for coding and use those codes for simulating the circuit in proteus,can You tell me how I can proceed?? Thanks
Hello, Can some one please help me to design a 3D visualization of a 7 -segment display using proteus . Dificult point I am facing is to design its top view to show segments. I dont have idea on adding few poligon to same view regards
Hello i want to add two number that two number is bigger than 20 and I want to display that in the seven segment with proteuse software my problem is i cant show 2 digit number in seven segment you can help me ? I dont want to programming !
i will suggest u to share the proteus file as well as the hex file so that we can tets it!
I get this error when i was running the proteus simulation for a 16f886 seven segment thermometer "PC=0x00A0 ADC conversion started before? wait ?time has expired following previous conversion or channel change" PC=0x016C ADC conversion started before? wait ?time has expired following previous conversion or channel change and the outpu
can u help me. If the stop button is pushed, metrobus will stop at the next station. There are four doors and each door is related with only three buttons (so 12 buttons in the bus). When a button is pushed, the related door should be opened. If there is no stop button caveat (warning), the bus passes the next station but it announces the station
hi i write the code 2 seven segment code in C, i test on proteus 6.9, fluctuating in display, i m use for(a=0;a<1275;a++)for(b=0;b<5;b++); timing. plz solve my proble.
Do one thing. You are using proteus for simulation rite? Do refer to the examples given in .DSN files for PIC16F877A & there you can find the same digital clock which you are trying to refer the code .asm in the corresponding project folder.This may help you. Regards, Jerin. :-) ---------- Post added at 04:22 -----
Plz can any one provide me 7 segment lcd display schematic for 8051 microcontrollers, and its code in c. i dont know much abt micrcontroller,and i cant simulate correct schematics whenever i build one. so plz give me some suggestion how to make schematics by my self in proteus and some good refrences. Thank You.
Hi, I work with proteus 7.2 to simulate a RC circuit. Now I want to see the real time while the circuit is working (i.e the proteus sow me the real time by itself or via any seven segment or any option it does.) Can somebody help me and let me know how to do so? Isthere any option in the software to do so? Thanks
Hi I am using proteus Ares for layout , but I can't find footprint for 4" 7segment common Cathod? Where can I get the foot print for it? Best Regards Hossam Alzomor www(.)i-g(.)org Added after 2 hours 3 minutes: Hi I made the symbol myself you can find it attached Salam Hossam Alzomor w
i have connected pic16f877 and 7segment led display through bcd to 7 seg driver(ic 4056).during simulation i receive the below error msg: no models specified for U3. (u3 is 4056). pls help to solve this problem thanks
Hello, first question is where to get proteus library with model of PIC16F819 /818 ? next, i have programmed my PIC16F819 chip, and connected 7 segment display to it like that: RB1 - a RB2 - b RB3 - c RB4 - d RB5 - e RB6 - f RB7 - g VSS connected to Gnd terminal of 7seg as needed. all connections are OK, programming was successfu
hi Labcenter model for this chip has wrong pin configuration and also segment out are not as per data sheet both things are fixed and added test stuff for LED display and LCD Display (required V7 proteus to simulate LCD
Hello Guys Im having this strange problem ; i made a little project having a couple of push buttons and 4 digit 7 segment display,thats ok , my problem is that i simulated everything on proteus and everything worked great Until i decided to downlaod the program on a pic16f876 , well strangly part of my program didnt work , for example i used time