Search Engine

47 Threads found on Usb Isp Programmer
Hello everyone, I am trying to program AT89S51 using a isp programmer and Progisp using usb port. But the microcontoller does not get programmed despite the Progisp's message saying that the operstion was successfull. Please help!
The default clock source of a meage0 is the internal RC so there is no need for a crystal. I'm not sure about the error cause because I haven't used ponyprog or a serial programmer, just parallel models and usb. Have you set the serial port correctly and the speed of the port from the PC hardware settings? Also make sure that you make the (...)
Hi, If you are after a programmer, then there are many cheap ones on ebay that work well. Heres just one
I programmed my ATmega16 using usb isp programmer. I have portD as output and port B as input. everything works just fine in Proteus simulation but in real, controller gives bipolar output (+2.5v & -2.5v approx.) on all 40 pins (except supply and input) :-o What may be the problem?
This design of isp programmer AVR910 was based on specification from Atmel (AVR910) . The programmer is based on processor AT90S2313-10, quartz 4MHz, load ver3.8b. The mai
popular programmers these days are usb . you will find a lot of them
The usbasp programmer is very popular. See here: Hope this helps. Tahmid.
No that will not be recognized in avr studio. You will have to use an external program like avrdude - - - Updated - - - To debug you need a jtag device like jtag ice. usbasp or AVRisp are just isp programmers. - - - Updated - - - Here is a DIY JTAGICE but it only works in AVR studio 4 if
Hello everyone, I tried everything before writing this. I was trying to connect an "ATMEGA 16A microcontroller" (which is impressed in a development board) with a "usb AVR programmer" by connecting through their isp header pins. I had connected them correctly using connecting wires. After that for checking whether i had (...)
Sir, I am trying to connect an "ATMEGA 16A microcontroller" (which is impressed in a development board) with a "usb AVR programmer" by connecting through their isp header pins. I had connected them correctly using connecting wires. After that for checking whether i had connected them correctly or not i had written (...)
i need schematic usb universal avr programmer with zif socket programming and isp please help regard
if 8051 is to be used for serial communication then for loopback
Hi, Assuming you have a usb port then to program a chip via isp then you need a simple programmer like this -
How do you mean open source? Open hardware for DIY or open code of programmer PC software or open code of firmware ? ---------- Post added at 16:17 ---------- Previous post was at 16:10 ---------- Check this programmer : AVR isp mkII usb programmer (AVRisp mkII clone) with (...)
support this family. list of supported controllers are- ATmega48 ATmega48P ATmega8 ATmega88 ATmega88P ATmega8515 ATmega8535 ATmega16 ATmega162 ATmeg164P ATmega165 ATmega165P ATmega168 ATmega168P ATmega169 ATmega169P ATmega32 ATmega324 ATmega324P ATmega325 ATmega325P ATmega3250 ATmega325
connectors often force us to stop using the devices based on LPT and COM ports. Presented device is useful and cheap. It starts with AVR isp programmer, which had converter system on a chip ARK3116S in the plug. Using this, usbasp was built. Attiny2313 was in the housing. The
Simplest to this is AVR isp programmer : Parallel (LPT) Port (Software ispprog or newer): 67510 Note: replacement for 74LVC244 can be 74HC244 while 74HCT244 cant. Serial (RS232) Port (Software PonyProg) : 67511 67512 usb version
flasher board is a board that enables user to flash the program or program the controller using isp or IAP technique... isp is In system programming and IAP is in application programming In These two techniques the first technique uses serial port / usb / Jtag programming device to be used for programming the controller.. This controller (...)
Recently I bought a usb isp for ATMEL AVR serires controller. (somewhat Similar to picture attached). I attached the programmer with ATMEGA128A chip with crystal & other basic components, the chip is being written & read, now I want to know for running the hardware which will include a 16x2 LCD I need to detach the isp & (...)
89c51 does not support isp. So you need a seperate programmer to program the IC, unlike P89v51 has the isp capability... Moreover, as far as , dont use usb to serial while programing the controller... Use serial cable instead.. if it is laptop then use it,, but cant guarentee if it works properly. See if you have 89c52 in (...)
for programming 89s52 a simple usb programmer that i came across is this: you cannot find any circuit simpler than this for programming through usb Yes, But it is hard to find 89c5131 You can get atmega8 all over
Hi. I've recently created an AVR isp programmer for ATMEGA8 and 16 with a parallel port interface to a PC and i use Ponyprog2000 for programming the microcontroller, it works fine. I am now working on C# application for programming these microcontrollers but i've encountered a problem, how will i actually write(burn hex file) and read from the mic
As 89S can be programmed in isp mode, Programming can be done by usb based programmer discussed in this thread. The popular usb asp can be modified to program 89S series too. Have a look. Cheers
Hi We are selling usb Atmega328 Arduino Boards in New Delhi India. The Advantages offered are:- 1) Can be converted into AVRDUDE (Arduinoisp) programmer. With jumper configured you can use ordinary 6 pin isp cable to program other boards. 2) Jumper to disable autoreset. 3) Superior Watchdog compatible (...)
Hello everyone, There are always many posts here asking about isp programmers for the atmel 89S51 or 89S52 mcu's. Most commonly available are the FREE programmers that use the parallel port of your PC. These programmers are not reliable, or do not work consistently on some parallel ports. If you happened to get stuck (...)
Hey I want to program the atmega324p controller. But when i saw the "usbasp AVR usb isp" programmer available in microstudio, it says that atmega324 is compatible with it but it doesn't say about the compatibility with atmega324p. Whats the difference between atmega324 and
You may convert the popular and simplest AVR programmer usb ASP to program 89sXX devices in isp. Refer this thread with similar discussions and links Cheers
I need a 89c/s series programmer pcb single side pcb!!!! Please do help me . . .
Here is all the info you need about usb based 89Sxx isp programmer Cheers Please Thank by the "Helped me" button
Check this Lot of people still searching for that... The present posibility is to use a serial programmer with usb to serial converter If any one found a stuff like that, please post it here Regards Nandhu
Hi! Anyone have schematic about MC AT 89S51 about board charge using usb, firmware ( if need)! thank For what it is used?:D
I have a usb programmer for Atmega8. I am familier with 8051 / 89s51 family and used it with isp programmer (using assembly language). I am not able to Blink a LED using Atmega8 microcontroller, I am new to this. Can some one suggest a simple schematic and assembly code (if possible with little logic behind). Thanks Raoof
I am using usbASP with AVR dude and with Prog isp and it works fine. But when used the same programmer with SinaProg, i get a message "Cant find programmer". Can anyone suggest a solution or point out the possible problem? I am using Windows XP Sp3 OS on my Laptop and use usb port.
Hi All, I have the TheCableAVR usb-isp programmer, but i could not successfully use it. i hope someone here can give me some ideas. I installed the programmer software and the usb driver, and the software TheCableAVR indicates the Cable is correctly connected with correct COM port. Then i loaded the .HEX (...)
Hi, I normally use PIC chips and dont really know anything about Atmel chips but I want to try a project with one. Please could someone point me in the direction of the schematic for a reasonably easy to build programmer for Atmel chips (like the ATMega8515). I'd prefer usb but serial is ok. (I assume I can't use my PICKit 2's?!?) T
Hi everyone! I used to use a Serial programmer for my microchip projects until today, but as everything changes, my new computer only has usb port and my serial programmer became "ancient history". Does anyone have a simple usb programmer schematic , with easily availabe components ? Tks in advance!
I need usb or serial port isp prog for AVR,
what kind of programmer are you using? I'll bet it's a parallel port isp programmer. are you able to program other devices with this programmer? Lots of problems with these programmers, best to buy or build one that works from serial port or usb port.
Once i do have the same problem. use usb to serial convertor. Most of the programmers will work fine with it. There are lot of serial programmers available. Regards Nandhu
hello i'd like programmers to programming AVR and 8051 by usb port
Yes, I do the same. Use usb to serial convertor Nandhu
Hi, I request you to please put source code of the firmware, so may be some one covert it to any usb supporting controller like 18F2550 or can use PICKIT2 hardware to programme 89S. Idea behind is to finally convert the simple PICKIT2 to a universal programmer. Thanks sadat007
I found this page very interesting: I want to make one of these programmers. I just want some feedback from people who have already made one of these circuits. Please reply Is it compatible with ponyprog? And is a GUI based software available for PC for the programmer?
Hi RollingEEE, I used Gogle and look what I was find. JURS
can some tell me where i can find a at89s52 programmer via usb, becouse i haven't com and lpt on my notebook.
isp at89s51 by usb? I think you can't find the solution. but you can send data with usb and programm with Parallel method.
hi you can visit the kitrus web page they have a usb programmer and it's free and good thing is that it can be used in isp mode