Search Engine www.edaboard.com

Adc And Proteus

Add Question

66 Threads found on edaboard.com: Adc And Proteus
I am using ATMega8A to read adc channel 0 and the code is working in proteus but not on hardware (EasyAVR v7). Here is the code. mikroC PRO AVR project and proteus files attached. Images show circuit, project settings and fuses. I tested LED blinking an all port pins (...)
I am using proteus to simulate an atmega32. So I load the code in but it doesnt seem like the interrupt is firing #include #include #ifndef F_CPU #define F_CPU 8000000UL #endif #define BAUD 9600 // define baud #define BAUDRATE ((F_CPU)/(BAUD*16UL)-1) void adcInitialize
Post the proteus file. Where is adc reading code ?
Hi, I'm simulating this circuit of battery charger in proteus and wondering how to convert the result into decimal numbers. Like 14.42 V instead of 14420 mV. PIC Simulator IDE code: 'PROGRAM TO CHARGE LEAD ACID BATTERIES WITH SOLAR PANEL 'USES PIC 16F877 AT 4 MHZ 'AUTHOR SANTHOSH JAYARAJAN 'NOTES: '*********************
Hello, I am designing a voice compression circuit and i use Tc7109 12-bit resolution adc in my circuit, the problem is there is no simulation model for this adc in multisim, orcad, or even proteus. How can I simulate this adc chip? Thanks for your concern.
I complied the code for using adc of lpc2138 in keil4. its hex file is generated but i cant simulate it in proteus. i included header file and all memory locations are correct still it is showing the error " attempt to read undefined register at address E0060010". What is wrong with the simulation?
ch is a char array ? Where are you reading adc ?
118087 that is the pattern and the code to vary the speed of a stepper motor with push-button how do this function with adc thank you char a,b; void interrupt() { if(intcon.rbif) { if(portb.b4==0) {a++;} if(portb.b5==0) {a--;} if(a==10) a=9; if(a==0) a=1; } intcon.rbif=0; } speed();void speed() {
I need to change duty cycle with adc module. I wrote a program and it changes duty cycle with a warning ("adc conversion started before wait time has expired following previous conversion or channel change") in proteus. how can I fix this ? how can I add a subprogram for interrup? thanks for your help. here (...)
coding for sending the data from adc to the lcd for displaying. m using 2 sensors interfaced with the adc like ldr and lm35 and want to send the data to lcd :roll:
can anybody plzz give the code and schematic diagram for following. i want to do display LCD using adc pins in atmega16. so i m in thought to do it for temperature display using LM35. so plzzzzz send me the code and schematic diagram and i want to execute it in proteus and then do (...)
For this I need to interface adc0809 for temperature sensor LM35 with 89v51and want to display temperature on LCD. But after creating HEX code in KEIL, I m facing problem during simulation in Software proteus. Issues: 1. No model specified for adc0809. 2. Simulation failed due to partition analysis error" I m not (...)
Can any one help me on this. I am working on voltmeter using the adc of pic6f877a with lcd , my code works perfect on proteus but when i implement it, it won't respond fine. At times it display, at times it don't. Pls i need help.
HI there, any help would be appreciated.. I am trying to read from the AD0831 adc through the SPI inteface in proteus lite sim . It seems that I have set the correct flags and every thing but the adc doesnot communiccate with the micocontroller at all. This is my configuration: SCK is RC3 SDI is RC4 SS is RA5. (...)
I am doing a project with PIC18F45K22. All the registers are configured properly. I am testing the project in both proteus and EasyPIC7. I see a strange problem. When the code inside while(1) executes all the status LEDs, PUMP relay etc... turn as expected but after the while(1) is exected successively then the first statement in while(1) loop whic
Have you disabled adc and other multiplexed function on RC0 and other pins used for MMC SD Card communication ? Post your complete mikroC project files. Zip and post your proteus file. Have you created an .mmc file to load into MMC model of proteus using winImage 8.9 ?
i had attached the code for lpc2129 which is compiled sucessfully in keil uvision 4 .but getting adc output of only 8 bits instead of 10 bits.checked with adc debugger in keil and also in terminal in isis proteus.kindly help me in this. #include "lpc21xx.h" #define Fosc 12000000 #define Fcclk (Fosc*5) #define (...)
I am making a temperature controller fan using lm35 and adc by pic16f877A, everything is okay but the reading of lm35 is fluctuated. LM35 readings are increment or decrement rapidly by increase or decrease a point in lm35 in proteus.
Looks to me more like a software problem. Your adc code is probably hanging somewhere.
Hi there! I am basically a newbie in microcontrollers and proteus VSM. I am not sure if i posted this on the right category. I want to create a project in proteus VSM using a microcontroller and I don't know which PIC16 IC will I use. I can't understand assembly but I have used Arduino for about six (...)