Search Engine www.edaboard.com

Adc Proteus

Add Question

89 Threads found on edaboard.com: Adc Proteus
Hi! I have one problem with proteus package for part LTC1864 adc. I try to change the package from DIL08 to TSSOP8 but the package gives me error (red circles) as shown in the attached figure from the PCB layout. Can anyone pointed out what is the problem? 136935 Thank you.
hi, does anybody know of 14 bit adc with spice model for simulation purpose? looking for similar in performance to AD9245. thanks!!
I am using ATMega8A to read adc channel 0 and the code is working in proteus but not on hardware (EasyAVR v7). Here is the code. mikroC PRO AVR project and proteus files attached. Images show circuit, project settings and fuses. I tested LED blinking an all port pins and they work fine. unsigned int adc_rd; (...)
what is the reason using while (1) in ISR and you do polling ISR code? have you checked the adc working with polling method only?
Post the proteus file. Where is adc reading code ?
Hi, I'm simulating this circuit of battery charger in proteus and wondering how to convert the result into decimal numbers. Like 14.42 V instead of 14420 mV. PIC Simulator IDE code: 'PROGRAM TO CHARGE LEAD ACID BATTERIES WITH SOLAR PANEL 'USES PIC 16F877 AT 4 MHZ 'AUTHOR SANTHOSH JAYARAJAN 'NOTES: '*********************
Hello, I am designing a voice compression circuit and i use Tc7109 12-bit resolution adc in my circuit, the problem is there is no simulation model for this adc in multisim, orcad, or even proteus. How can I simulate this adc chip? Thanks for your concern.
I am trying to read adc in atmeg 32 .Displaying the data to lcd to a vlot /ammeter project . my problem whenever simulate it on proteus it will hangup on the checking of ADSC conversion /* * vmam.c * * Created: 14-Oct-15 6:44:15 PM * Author: Krishna */ #define F_CPU 16000000UL #include #include #include"l
I complied the code for using adc of lpc2138 in keil4. its hex file is generated but i cant simulate it in proteus. i included header file and all memory locations are correct still it is showing the error " attempt to read undefined register at address E0060010". What is wrong with the simulation?
ch is a char array ? Where are you reading adc ?
118087 that is the pattern and the code to vary the speed of a stepper motor with push-button how do this function with adc thank you char a,b; void interrupt() { if(intcon.rbif) { if(portb.b4==0) {a++;} if(portb.b5==0) {a--;} if(a==10) a=9; if(a==0) a=1; } intcon.rbif=0; } speed();void speed() {
I need to change duty cycle with adc module. I wrote a program and it changes duty cycle with a warning ("adc conversion started before wait time has expired following previous conversion or channel change") in proteus. how can I fix this ? how can I add a subprogram for interrup? thanks for your help. here is my code: #
hello there i am trying to use the adc0808 with the microcontroller 8051 for a bigger project, so i wanted to test if i get correct output from the adc. To do this i made a temporary circuit and connected data pins to p3, eoc sc clock and ale to the port 0(used pull up too) and i am using only 1 input so i have kept others open and given address ab
coding for sending the data from adc to the lcd for displaying. m using 2 sensors interfaced with the adc like ldr and lm35 and want to send the data to lcd :roll:
can anybody plzz give the code and schematic diagram for following. i want to do display LCD using adc pins in atmega16. so i m in thought to do it for temperature display using LM35. so plzzzzz send me the code and schematic diagram and i want to execute it in proteus and then do hardware.......plz do help me........awaiting for reply.......
For this I need to interface adc0809 for temperature sensor LM35 with 89v51and want to display temperature on LCD. But after creating HEX code in KEIL, I m facing problem during simulation in Software proteus. Issues: 1. No model specified for adc0809. 2. Simulation failed due to partition analysis error" I m not getting the (...)
Can any one help me on this. I am working on voltmeter using the adc of pic6f877a with lcd , my code works perfect on proteus but when i implement it, it won't respond fine. At times it display, at times it don't. Pls i need help.
Hello there, i have this mikrobasic code but my problem is that i don't know how to modify it so it can work with voltages higher than 5 volts. The uC i'm using is PIC16F676 which has an internal adc module. Maybe if i make Vref different than Vdd and i do tie that pin to a different reference i.e 1.25V and then using an op amp to downsize the v
HI there, any help would be appreciated.. I am trying to read from the AD0831 adc through the SPI inteface in proteus lite sim . It seems that I have set the correct flags and every thing but the adc doesnot communiccate with the micocontroller at all. This is my configuration: SCK is RC3 SDI is RC4 SS is RA5. I think the (...)
I am doing a project with PIC18F45K22. All the registers are configured properly. I am testing the project in both proteus and EasyPIC7. I see a strange problem. When the code inside while(1) executes all the status LEDs, PUMP relay etc... turn as expected but after the while(1) is exected successively then the first statement in while(1) loop whic