Search Engine www.edaboard.com

Antenna And ie3d

Add Question

264 Threads found on edaboard.com: Antenna And ie3d
Hi, I want to perform Characteristic Mode Analysis using MATLAB of a handset antenna. I don't have FEKO licensed version. I am familiar with CST and ie3d. In this regard I have two questions: 1. Can I use any of these EM softwares (CST/ie3d) for characteristic mode analysis? 2. Can anyone help me in (...)
Hi, I want to perform Characteristic Mode Analysis using MATLAB of a handset antenna. I don't have FEKO licensed version. I am familiar with CST and ie3d. In this regard I have two questions: 1. Can I use any of these EM softwares (CST/ie3d) for characteristic mode analysis? 2. Can anyone help me in (...)
Hello, I want to ask, have you find the way to calculate the AR value from the measured graphs of antenna? plz rep. Thanks
The example is operating at 10GHz. For your requirement, you should change the antennas size. The antenna is comrised of a shape, and the shape is comprised of several vertices. To change the antennas size, you should change the vertices.
Hi all, from long time i am trying to simulate PIFA antenna in ie3d software, bt nt able to draw vertical plane.. hey guys plz help me as i am new to software .. i am using Zeland 12.0 version thank you.
Hello, In ie3d first I am using the patch with Infinte ground plane. The results were quite good.But when I use the finite ground the results are not upto the mark. Can any one suggest that how can I include the finite ground in microstrip antenna. and after inserting it what is the procedure of cutting the slots in ground plane (...)
Dear all .. what is the procedure of simulation of phased array antenna along with the components like resistor, capacitor, varactor and pin diode in ie3d or CST MWS. Can you please send the link for such documents. Thanks
plz.. help me to construct a stacked microstrip patch antenna in zeland ie3d.... how to joint a single feed to both the antennas in stacked configuration both in software as well as hardware? and please tell me the procedure how to do probe feeding to yeald at maximum gain.
I had simulated micro patch antenna for 2.4 ghz and I can find s11 but please explain procedures to find other results like far feild radiation, near feild,efficiency,gain,directivity and all parameters
here is my antenna file from ie3d .i tried for 2.4 GHz but i don't know how to correct this to operate at 2.4 GHz please find the attachment and correct this one for me and let me know where i committed mistake.115800
please tel me in ie3d where we can get pin diode and how we can use this for reconfiguration..
I want to design an antenna element in ie3d.The antenna consists of a pair of folded dipoles.The dipoles are coupling fed by an L-shaped microstrip line.The dipoles are printed on backside of the substrate while the L-shaped microstrip line is etched on the front side of the same substrate and it is fed using a 50ohm coaxial (...)
Hi All, I set up an ie3d model to a PCB PIFA antenna, following the dimension and paramters from a paper by Texas Instrument. Attached is the paper decriptions download from TI website, and the geo file together with simulation configuration file setup by me. 111809 However, my simulation results are far worse than the (...)
the circular match antenna raidus is taken as 27.7mm While modelling the coaxial probe feed to patch , the inner and outer diameters of the probe are taken as 1.3mm and 4.1mm respectively. it is loacated at a radial distance of 9.9mm fromthe center of patch towards its cicrcumference. A shorting patch is located at center with radius 0.5mm (...)
Wrong forum. Moved to the RF, Microwave, antennas and Optics forum. erikl
Hello everyone.. I need some help in implementing chip resistor in a patch antenna in ie3d in vertical direction i.e between the top metal patch layer and the finite ground plane in vertical direction. I am doing this for reducing size of the antenna.. Thank you..
hello everyone, i am doing project on uwb antenna however i am not aware of how to simulate plana monopole antenna in ie3d plz if ne1 can help me with the detailed steps regarding the simulation and procedure? i know how to use ie3d thank you
Hello to everyone, i am using ie3d to simulate an antenna. I will use for conductor Gold or Copper. I am searching about relative constant and Loss tangent δ. Ιs anyone knows these value in Microwave Band? Also, in optical frequencies is there any significant deviation ? Bests, George
hi, please send me above specification .geo file.... m stuck with trial and error method. further i need to implement wilkinson pwer divider. so please send me .geo file with FINITE ground plane. m working on ie3d
This is a classic problem that all classic antenna text books (Balanis, Volakis, Stutzman , Kraus ...) cover, as well as most of the software such as HFSS, CST, FEKO, WIPLD, ie3d ....