Search Engine www.edaboard.com

Calibration Kit

Add Question

1000 Threads found on edaboard.com: Calibration Kit
I am working on a kind of self project to driver a motor using the micro chip kit. Now i want to make a kind of complete application solution for commercial purpose. What are the applications i can work on? How do i approach? Any ideas or suggestions.
When I try to zoom in order to see the layers of the device ,I tried to increase stop in options > display but it shows me a box with a cross on it.your help appreciated 154227 154228 154229
Are you an Entrepreneur looking to get into the Uber business? Let Us Teach You How to Start Your Uber Business. In these posts, filled with our expertise and tips, we walk you through the sign up process, as well as the necessary preparation, and ongoing business management secrets to help you launch and sustain a profitable rideshare business.
Are MEMS sensors are available in analog form? Sure, that's why I suggested it. The advantage is easy calibration of measurement output.
Hello, For Analog Mixed Signal Layout in CMOS in 65nm and blow, what finger size and multiplier should be used ? I have been told to avoid multipliers unless in cases of Common Centroid layout. Also, what finger size to pick ? Someone recommended to me W < 20 ∗ L at lower or at 65nm CMOS for the size of each finger (so for 65nm -
Hi, Say total gate width = constant = number of fingers*finger width. Does it impact Efficiency and power gain in a power amplifier, how I chose the number of fingers and finger width. More fingers and small finger width or less fingers and large finger width?
Hi, I used TSMC 65 nm technology in my design. There is a varactor which is moscap_rf. I want to use it in my design. I want to ask that what is the maximum level for Vdd in this design. I could not find it. If you can help me , I will be glad. Thank you so much already.
In addition to etching and milling PCBs, there is nowadays also a technique for manufacturing PCBs by printing webs with a conductive material on a carrier, this is what my teacher said but i cant find any machine that does this and offcourse im a beginner, can someone pls help me bij just give a machine that does this, only the machine name is eno
Are you an Entrepreneur looking to get into the Uber business? Let Us Teach You How to Start Your Uber Business. In these posts, filled with our expertise and tips, we walk you through the sign up process, as well as the necessary preparation, and ongoing business management secrets to help you launch and sustain a profitable rideshare business.
For this frequency range, I like the VNWA3. It offers more advanced port calibration than many other entry level VNA.
I appreciate your intention, but I fear there's no simple technical solution. Ion mobility spectrometry (IMS) is a technique that can be possibly implemented in DIY instruments, but it's rather unspecific, detecting a large number of compounds. It would also require calibration with real explosive samples.
Please help me understand what is going wrong with my importing. I am trying to import a 0402 100pF capacitor from Murata into ADS. I am suppose to get a bunch of components with pins connected after the import, but I do not, I only get pin 1 and pin 2. Here are some pictures of the process I do to import the file below. Idk if it has to do with th
As far as I see, there's no specification of typical uncalibrated CS5490 scaling. However, the internal reference is too inaccurate to use the chip without calibration. In so far the question of uncalibrated scaling factor is interesting but doesn't need an exact answer, I think.
Hi, Do some"calibration tests": Put the sensor on the table and fix it with a tape. (Maybe mark it's position and direction on the table with a pen) * do the measurement an write down the values (best if you do a couple of measurements to get a clue about fluctuation and noise. You may also cancel out some noise by taking the average) * the move t
I am using TI Tiva launchpad and my Blinky code is not working. This is th elaunchpad I am and other project settings are fine because I copied them from mikroe MINI-M4-Tiva example Blink a
Hi, I've been trying to do a layout on the NCSU Design kit provided technology (AMI0.6u). I am testing a layout on a simple inverter. Everything works great initially, I was able to do DRC, Extracted, and LVS and pass. However, it suddenly won't work today once I want to do a LVS again without me doing any modification. The error me
Temperature coefficient of sensor which I am using is 0.02%F.S./ ℃ With this coefficient and measuring the temperature using temp. sensor. Is it possible to derive the equation to compensate for different temperature? There's no equation to derive, just an empirical error function that can be recorded for each sensor exem
I have been using a Remington PG6025 All-in-1 lithium powered grooming kit. It is very powerful. The battery lasts long. There is an article about this hair cutting kit. If you want to know to buy or want to know more about this kit, visit
Hello thank you for your interest in my problem. actually my ground pins were placed a little bit randomly. So I read your document about edges/area pin and used edge ports for my ground pins (picture 1) but the pin for the cpw line is defined as a dot (P1 on my picture). so I have a few questions. first of all when I cr
First, you need to use the microstrip schematic models properly, including MSTEP, MCROS and MLOC. It is not accurate to just cascade MLIN with very different width. There are examples included with ADS. One example how to build this structure from schematic models: N