Search Engine www.edaboard.com

Calibration Kit

Add Question

1000 Threads found on edaboard.com: Calibration Kit
156484 PCB Solar Panel kit Monitor Box Hi All, I have a solar kit for camping that has a plug in monitor box. The wires to the PCB inside were soldered poorly and have come loose I am unable to work out what wire goes where. There is 4 wires Red, Black, White and Green and 4 soldered areas where the wires were
Using the kT/C noise to calculate the unit cap is a reasonable approach. MOM caps usually used in the design of the cap dac for SARs match pretty well, maybe up to 10 bit accuracy and they keep their matching for many years. For 12 bit dac you may need to think of some sort of calibration for the first 2-3 MSB caps. Or use redundancy in the dac whi
Hello members, Which RTOS do you all suggest for STM32F429? Thanks in advance, Embedded Geek
A general solution that doesn't depend on a specific camera position and lens properties would be a calibration grid placed on the playground. Then determine a mapping function (e.g. 2-D look-up table) that calculates x-y coordinates for pixel positions.
I am trying to do some free space calibration to extract material data from unknown arbitrary material. I am struggling with the calibration part as the s parameters i am getting is not good enough to get proper value. Can anybody please suggest the calibration procedure? I have E8361 keysight VNA. I have Type N short, open, load, through (...)
Hi all, I am now designing a power amplifier (PA) at 2.4 GHz using microstrip lines as input and output matching networks on a Rogers 4350B substrate. This PA was designed using the harmonic termination technique. Simulation substrate parameters of this substrate are given in its datasheet. Input matching network (IMN) was treated to 2f0 while o
Hello everyone, I have used some RF test points to characterize the RF components of a S-band receiver prototype. The part numbers are: MS-156C3 for the RF test points; MS-156-HRMJ-H1 for the plug (the mate-connector). Since I would like to measure the S-parameters, I need to use a calibration kit for the network analyzer. My q
Have with few microntrollers. Trying to learn psoc technologies. What psoc is good to start with?. Considering the easiness to start learning the psoc and the low cost what is recommended?.
Hello, Has anyone used this NCSU kit for Analog Design ? Or is it mainly for digital design (standard cell flow). Thank you.
Hi to all! Help me please to solve a problem during simulation a model of MRF 13750 in ADS. See attached file.
Is the noise there with the scope tip grounded or connected to the scope calibration signal?
Dear all, I'm facing a problem with a post-pnr simulation that I hope you can help me figure out. The design flow is based on the GPDK045 kit from Cadence. I use Genus & Innovus for synthesis & pnr, Modelsim for simulations, and I have compiled the standard cell library with modelsim for gate-level simulations. Post-synthesis, my timing co
Dear all, I am having a problem with a post-pnr simulation that I hope you can help me figure out. The design flow relies on the GPDK045 kit from Cadence. I use Genus & Innovus for synthesis & pnr, and Modelsim for simulations. I have compiled the standard cells with Modelsim for gate level simulations. Post-synthesis the timing constraint
thanks Sir how to get the calibration value of the internal oscillator to move it to OSCCAL ? i see in my code call 0x1ff before movwf OSCCAL but when assembling it gives me error of "Call or jump not allowed at this address (must be in low half of page" i think i have a problem with the calibration of the oscillator thanks for help
I am having my project requirement to sample the analog data at the rate of 2 Mega samples per second streaming data and send to the PC. I am thinking to use PIC starter kit with USB or Ethernet with demo software for PC side to receive and download the PIC data. I just look at some Microchip starter kits but I am not sure I can use them for my app
Let's say following Yocto project image or embedded linux distribution was created by using remote virtual linux box from windows computer: Image Name: fsl-image-validation-imx Target: Builds an image with a GUI without any Qt content. Please refer to section 5.2 in attached i.MX_Yocto_Project_User's_Guide.pdf The created filename
How is the mains so stable in large cities like London?....surely it is because there are thousands of micro generators all over London, with regulating tap changers on their transformers?...otherwise there would be horrendous load regulation problems leading to low mains voltages.
Spikes in noise suggest that there's still something connected to the channel input. If not, it's input DC offset, can be often removed with oscilloscope calibration procedure. Check the manual. - - - Updated - - - Question was already answered. Read manual about Utility/Self Adjust function.
Yes, it's possible to use a cheaper SA at higher Frequencies using with a Mixer but an accurate calibration must be done because Frequency Response of the Mixer is not flat at all. Also, spurs and naturally created harmonics that will a obvious results of the Operation of Mixer may be troublesome and they have to be well filtered.One more, Input Se
Datasheet says that individual adjustment (calibration) with alcohole vapour/air mixture is necessary. Resistance value of MQ-3 is difference to various kinds and various concentration gases. So, when using this components, sensitivity adjustment is very necessary. we recommend that you calibrate the detector for 0.4mg/L (approximately 20