Search Engine www.edaboard.com

Configuration ic5141

Add Question

1000 Threads found on edaboard.com: Configuration ic5141
I am working with gnss sdr software for processing rf signal captured in file. In gnss sdr software configuration the data source mentions adc sampling rate and type as i and q samples. Nothing is mentioned about IF frequency. Does that mean the intermediate frequency is always zero for I and Q components?
Hello, I am trying a 2 cases setup like this where there will be 2 horn antenna facing each other and S parameter data will be extracted. For the 2nd case using the similar setup there will be a large metal plate in the middle of the line of sight of horn antenna. I should expect antenna with metal plate, the S parameter value should be very
Hi all, I'm trying to diagnose a potential issue with my computer monitor causing me eyestrain in Linux with the Nvidia proprietary driver. The screen almost appears to have an almost imperceptible shimmering effect which causes eyestrain and a onset of a headache within minutes. I get no eyestrain in Windows, nor does it occur with Linux runnin
D6 may have to be a fast switching type, possibly a Schottky diode but a 1N4148 will probably do. The actual output voltage is set by R5 and R20 but if I had to guess at the fault it would be either C20 or C35. The Ic manufacturer recommends a PC817 optocoupler in that configuration. They are cheap and plentiful. Brian.
The obvious/trivial answer is change the opamp to an inverting configuration. Or, if your input is floating, just swap the return and signal.
Hey Guys, I am new to this forum. I just wanted some help regarding the Lt3750 chip. I have read the previous threads on the same.. I didn't want to reply on that since it is too old. I have designed my PCB for charging a 470uF 400V Cap with a 6A configuration 300V circuit configuration. I have followed the recommended design for the PCB and als
I'm implementing a PCM2706 in an audio amplifier that I'm designing. I've read through the datasheet and I think I've figured most of it out, but it's the part regarding 'device descriptors' that I'm a little stuck with. The datasheet says the following: 9.3.6 Descriptor Data Modification The descriptor data can be modified through the I
Hi guys, Can anybody tell me what's this configuration please? I have found this strange configuration on a strange circuit & i need to know what's the purpose of that? 157021
Connecting your voltage amplifier in transimpedance configuration should achieve what you want. According to the gain plot (no phase response shown, unfortunately), it's questionable if you achieve sufficient phase margin for stable operation. Miller compensation may need adjustment.
Hi all, I got the part from the specified library itself. anl_misc.lib. - - - Updated - - - hi all, I got it. the library was missing. Pspice tab -> Edit Simulation Profile -> configuration Files -> Category Library -> Browse -> Cadence - SPB xx -> tools -> pspice -> library -> anl_misc.lib and then Add to
Hi, The following XC8 C Code just reads the ADC input?then if above a certain value, it then outputs a PWM out on a pin. Do you think this code is OK? it builds fine. The ADC had loads of registers and it didnt look like you had to bother setting all of them? It would be good if microchip had like an "LTspice simulator " for their microcon
Hi, I connected the ADC0 input with the 5v pin of the pi are you sure 5V is within the specified ADC input range? What output value do you expect with this configuration. What range of ouput values do you see? **** Generally: No input (independent of used or not) should be left floating. Be sure to have valid levels on [
Do you understand MNPC topology? Do you understand the purpose of split output feature? What kind of c
I understand that Klaus but it doesn't increase 10 bits to 12 bits, it just multiplies the result by 4, the LSB will always be zero. The ADC is still 10 bits. Some Arduino device can use 12-bit resolution natively but I think they require some register configuration. Brian.
Hi i have a 2inch spi tft lcd with st7735 driver and i run emwin library on it using stm32f103ve. i dont use external ram for emwin and just use micro ram for emwin. i can use all of emwin capability except memory device. i try evrything but memory devices wont work. is that because of i dont use external ram or memory devices wont work on spi lcd
hellow guys iam writing a simple bootloader on a stm32f103ve microcontroller from address 0x8008000 and a userapp code from address 0x8008000 my bootloader code include uart1 configuratin for show some massages and spi2 configuration for communication to a spiflash and my userapp code include timer6 , timer 7 configuration for two led blink wit
From an installed programming specialist's perspective, a vehicle has become a versatile box brimming with implanted frameworks. This article surveys all parts of installed programming in autos, including working frameworks, conventions, improvement apparatuses and universal gauges. Until around the turn of this century, there were not many ele
From an installed programming specialist's perspective, a vehicle has become a versatile box brimming with implanted frameworks. This article surveys all parts of installed programming in autos, including working frameworks, conventions, improvement apparatuses and universal gauges. Until around the turn of this century, there were not many ele
long story short: making pwm motor driver circuit for as apart of my senior design project, trying to get TI's DRV8874 transient model to simulate inside of orcad. I believe I followed all of the info in the data sheet and it's not reacting to anything. Also, im fairly sure i imported the model correctly, imported the orcad file then tied library f
long story short: making pwm motor driver circuit for my senior design project, trying to get TI's DRV8874 transient model to simulate inside of orcad. I believe I followed all of the info in the data sheet and it's not reacting to anything. Also, im fairly sure i imported the model correctly, imported the orcad file then tied library file to it to


Last searching phrases:

arquivos | circa | coherently | tetris | epcos | varistors | topmost | prompt | panic | nevertheless