Search Engine


Add Question

Are you looking for?:
hd44780 pic , lcd hd44780 , hd44780 lcd , hd44780 avr
208 Threads found on hd44780
Hello, i'm trying to initialize an lcd hd44780 using a 16F887 microcontroller but it seems that something is wrong with the code. include temp1 equ h'20' temp2 equ h'21' temp3 equ h'22' org h'0000' nop bsf STATUS,RP0 bcf TRISD,0 bcf STATUS,RP0 bcf PORTD,0 ;stelnei 0 bsf STATUS,RP0 bcf TRISD,1
The function set of hd44780 lcds have only two options i.e two lines disply or one line display...How can i select 4 line display for 16*4 LCD??
I think the question title is misleading, you apparently mean interfacing the hd44780 in Verilog, not implementing it? If the project possibly implies designing a hd44780 model for test purposes (you don't clearly tell about this point), it can only apply to the digital part (bus interface and controller) not the analog part (LCD driver). The latte
I'm trying to show big numbers on a 2x16 character lcd. For this i defined custom patterns to form big numbers in the CGRAM. But CGRAM is limited so i tried to load the CGRAM with the number that will be displayed at that moment. For example I'm loading 0 to CGRAM and displaying it than i'm loading 1 to CGRAm and displaying it on another place but
Most LCDs have similar setups, take a look at these examples: FPGA4Fun's LCD Tutorial Interfacing hd44780 LCD PDF These should get you rolling.
i am interfacing the DS1621 with 89s52 and displaying it on the hitachi based hd44780 ...16X2 LCD Problem with code i have is not display the value of the temperature .. instead it is showing helloword || %d%s|| centigarde and garbage value .... i want helloworld 30 centigrades so please help me ... i will be so thnkful
made this project just for curious, what can I do with Attiny13? Answer is “a lot”. In this case, it can measure voltage, current, temperature, calculate data, and show results in simple way at alphanumerical display ( type hd44780). That’s not all, software ha
Seems that this display uses an hd44780 controller. Now for the commands you've to check the datasheet of the controller, e.g. here:
Hello forum :-) I am working on a project, I am currently trying to get some LCD code attached to drive my LCD, the LCD is hd44780 compatible and the driver is written for it. However, my circuit has a 20Mhz crystal so I think the delays that are defined at the beginning of the code must be incorrect. Could someone please help with this. I have
hi, i have a at89c51 and hd44780 lcd..i want to interface these with each other....i don't have the circuit diagram so please provide me..... please...........
would like to present testing board for my brother.Heart of the system is Atmeg32 or 16 ( in this case it is atmeg32). It consist possibility of working with those displays: LCD hd44780, PCF8833 (nokia 6100/6610i), LSO20 (siemens S65/cx70), Two 7-leg LED displays LED ruler Mat
Hi, For microcontroller use AVR or PIC or anything else. I suggest AVR. For display, you can use GLCD with controller KS108/KS107/T6963 or you can use alphanumeric LCD with controller hd44780. Tahmid.
Similar unresolved thread: Better contact your vendor about the data sheet. Else as Tahmid said try comparing your module with standard Hitachi hd44780.
Hi, If you select LCD with hd44780 controller or similar, there is a command for display/cursor shift. m.
Hi, That code should run fine on your 690 with any parallel hd44780 compatible lcd. Although the data ends up in the lcd, there are several slightly different ways of collecting and outputting the data. The Mikro is one way, but do not spend a lot of time trying to understand what is quite a complicated routine - just use it and concentra
hey guyz i'm having a problem in programming an LCD my LCD is LM052L it has a built in LSI hd44780 and i'm using a pic16f877a i don't know what's the problem. this is my picbasic program: Device=16F877A XTAL=4 ALL_DIGITAL=true TRISC=0 LCD_DTPIN=PORTC.0 'CALL ASSIGNED ADDRESS TO PORTC.0 LCD_RSPIN=PORTC.4 LCD_ENPIN=PORTC.5 LCD
Dear all, I want to use a hd44780 for a hobby circuit. So I have connected with my PIC MCU in a 4-wire interface and tried to communicate with it. However I cannot display anything on the LCD. I will try to troubleshoot my design but I need to know something pretty important! I cannot understand whether the LCD has been initialized or not..(
Hey All , One simple question , I'm using hd44780 lcd 4 line , I did control the LCD , and but i couldn't understand from the websites how can i display for example "A" at the 4 lines , how can i do that please ? and if there is an c code example would be great , cuz to understand better need some example , ?? thanks alot .
First, you have to realize how the memory in an LCD is mapped. The two rows in memory aren't separate. Assuming you are using an hd44780-based display, the first row starts at like 0x00 and the second row starts at like 0x40. If you want to scroll just the second row, you need to write your own routine that will only shift the characters over from
LCD Interfacing if your LCD Module uses a hd44780-based controller (or similar, many are these days): and datasheet: Humidity sensors introduction: Google is yo