Search Engine www.edaboard.com

hd44780 Lcd

Add Question

195 Threads found on edaboard.com: hd44780 Lcd
in JHD162A JHD is the Company Name/etc 162 mean 16x2 but this lcd uses the same controller hd44780
Generally, TrickyDicky is right about the necessicity to register asynchronous inputs to a state machine (or other synchronous logic). Ignoring this requirement is one of the most favourite methods to cause occasional failure of a design. In the present case, db_in(7) is effectively copied to a single register if db_in(7) = '0' then check
I hooked up a Hitachi hd44780 based 2x16 lcd with PIC18F2420. Now on the bootup, I should see boxes in the top row (Typical for a hd44780 based lcd). But what I see is 8 boxes in top row and 8 boxes in Bottom row. Is the lcd Blown or something else is wrong? I have attached a snapshot of (...)
lcds with hd44780 controllers are nice, but you can also reuse lcds from old mobile phones. The best place to start is Nokia 3310 lcd which you connect to your micro with only 3-4 wires I think (SPI or IIC is there). The only issue is that you have to run your MCU with 3.3V or use voltage dividers with resistors. (...)
I have always found this page good for the lcd info lcd hd44780 comands
Try reading through the board, there are lots of threads/replies on the subject of displaying contents on lcd, read the datasheet of lcd, normally its hd44780. Keep the sample code and datasheet side by side and you will understand the command structure. If you are using C for programming both Hitech and CCS have sample code in their directories.
Hi, Use any regular lcd (hd44780 controller) and write Bangla characters as custom characters. Which compiler do you use? In mikroBASIC, mikroC and mikroPASCAL, there are tools for visually creating the character and the tool automatically generates the code for the function required to display that custom character on the lcd. Hope this (...)
Hello, I have a system consisted of a SIM300D, PIC16f877A and a hd44780 lcd. I am also writing in CCS compiler. What i am trying to do is, to make a gprs connection with the sim300d and send data from pic. The test code which i am trying to read a response is the following: while(1){ delay_ms(1000); //Print to lcd the
Please check the following code of PIC16F877 with lcd interfaced. ;------------------------------------------------------------------------------------------------------------------------ ; Source code for the PIC16F877A based interfacing with hd44780 based 16x2 lcd. (...)
My lcd still cant display the word. My lcd is hd44780 16x2. This my code. ;------------------------------------------------------------------------------------------------------------------------ ; Source code for the PIC16F876A based interfacing with hd44780 based 16x2 lcd. (...)
Some times a character based lcd (hd44780) can pickup noise or lost synchronization with the controller. 1- What do you suggest to protect inputs to prevent from getting unwanted noise (commands, data). 2- If it gets noise and display is garbaged, what can i do to correct it in the controller. I would like to hear you suggestions, thanks.
Hello, i'm trying to initialize an lcd hd44780 using a 16F887 microcontroller but it seems that something is wrong with the code. include temp1 equ h'20' temp2 equ h'21' temp3 equ h'22' org h'0000' nop bsf STATUS,RP0 bcf TRISD,0 bcf STATUS,RP0 bcf PORTD,0 ;stelnei 0 bsf STATUS,RP0 bcf TRISD,1
The function set of hd44780 lcds have only two options i.e two lines disply or one line display...How can i select 4 line display for 16*4 lcd??
I think the question title is misleading, you apparently mean interfacing the hd44780 in Verilog, not implementing it? If the project possibly implies designing a hd44780 model for test purposes (you don't clearly tell about this point), it can only apply to the digital part (bus interface and controller) not the analog part (lcd driver). (...)
I'm trying to show big numbers on a 2x16 character lcd. For this i defined custom patterns to form big numbers in the CGRAM. But CGRAM is limited so i tried to load the CGRAM with the number that will be displayed at that moment. For example I'm loading 0 to CGRAM and displaying it than i'm loading 1 to CGRAm and displaying it on another place but
Most lcds have similar setups, take a look at these examples: FPGA4Fun's lcd Tutorial Interfacing hd44780 lcd PDF These should get you rolling.
i am interfacing the DS1621 with 89s52 and displaying it on the hitachi based hd44780 ...16X2 lcd Problem with code i have is not display the value of the temperature .. instead it is showing helloword || %d%s|| centigarde and garbage value .... i want helloworld 30 centigrades so please help me ... i will be so thnkful
Seems that this display uses an hd44780 controller. Now for the commands you've to check the datasheet of the controller, e.g. here:
Hello forum :-) I am working on a project, I am currently trying to get some lcd code attached to drive my lcd, the lcd is hd44780 compatible and the driver is written for it. However, my circuit has a 20Mhz crystal so I think the delays that are defined at the beginning of the code must be incorrect. Could someone (...)
hi, i have a at89c51 and hd44780 lcd..i want to interface these with each other....i don't have the circuit diagram so please provide me..... please...........