Search Engine www.edaboard.com

311 Threads found on edaboard.com: Hyper Terminal
Hi, you donīt tell wich interface.. But "hyperterminal" sounds like you use RS232 or TTL_UART. --> My hint: baud rate setting, baud rate error, wrong UART setting. Klaus
HI, i sent at command "AT+CSCLK" through hyper terminal and responded as ok. after that the sim900 is not at all responding to any of the commands. what is the problem with at+csclk" command . i dont know what this command does actually. please reply me . i need help .
Guys, I'm trying to interface gps module mt3333 with 8051 but unsuccessful til now. My gps module is not showing me proper values in hyper terminal, i.e. it is not showing me latitude or longitude. Also in $GPRMC statement it is showing a letter 'V' which stands for data not valid. So can anyone help me with this so that it shows me latitude and l
Hi guys, I'm having a ICP CON rs232 to rs485 converter. I dont know how to check whether it is working or not?. I've only one rs232 to rs485 converter and usb to serial converter. My rs232 to rs485 converter has a operating voltage is 10-30v dc. i gave power supply of 12v dc with 1A. Rs232 to Rs485 converter's other end is connected t
Hi All. I am passing very hard time with my Telit Module to activate the GPRS from MCU UART. I know the EasyGPRS AT Commands to Activate GPRS and send UDP Data. The strange issue is ... when I an sending the AT Command manuallly by typing from PC hyper-terminal then all works. Module can send UDP Data to Server. But when I am sending exact sa
Hi all, i am trying to send a data to server using sim900 gsm module interfaced with arduino uno. (I have laptop ,so can't use hyper terminal).The TCP connection is established, but the post command replies like below...and i can't send data. please help me... AT+CIPSEND AT+CIPSEND > POST /webservices/tempconvert.asmx/CelsiusToFahre
I need to simulate a GSM modem. I don't know if someone here has done it before, i would love to see it. i just need it to verify a number things before going ahead with my project using proteus and modelling the modem using the hyper-terminal
hi dear friend I'm working with sim900 (sim 900 doesn't answer my at command just reply every thing that I send, back) and when I turning the sim900 off send "NORMAL POWER DOWN" on hyper terminal:bang::bang::bang::bang: (cry cry cry) help me please
Hello dear friends, Please guide me against the following problem: I am trying to develop uart communication between PIC 16F877A (20 MHz crystal) and PC using hyper terminal. I wrote the following simple code in mikroc Pro v.6.5.0 compiler to run: char RS; void main() { TRISC = 0xF0; Uart1_Init(9600); whi
what is your observation about test gsm module with hyper terminal first and check the avr and GSM RX,TX connections.
Hi there, I'm a newbie and tried to dial a no from MCU (16F887) to Sony Erricsson K750i. With hyper terminal connected with data cable to pc it works AT commands fine.But I couldn't communicate SE750i with MCU. I have attached schematic I used (drawn by me) and the flowcode program that I used. Please help me to get this done, really appreciate.
ok detach the micro controller or its board and check the module with the PC using hyper terminal make sure it is working good if so then something wrong with code or the hardware which contains the micro controller. use a switching 3A sullpy that i have tested it under 3.5A. I don't know how did you test it?
SPBRG=64;//4800 bps for 20 Mhz crystal check your gsm is running with same baud rate. try with 9600 baud rate.Test your gsm with hyper terminal first.
1.how to test a GSM module. 2.before connecting hyper terminal. 3. because send and receive problem in hyperterminal ? on loop connection it works properly but in modem? 1(Ans) You can test your GSM with hyper terminal or with stand alone controller with AT commands. 2and (...)
hi i want to convert i2c protocol come from master pic micro controller to rs232 to help me to read it via hyper terminal. rely i am not the protocol i want microc code and protues design any one help me
hi i want to interface my gps board with raspberry pi......now i got the data when connecte to hyper terminal. how can i interface this can anyone give my some idea.
Hello everyone, i am new in edaboard as well as GPS module. i connected my GPS module to PC with baud rate 9600 and see the results on putty ar hyper terminal. but results are not according to my location.. like time latitude longitude direction are not accurate... i try to see it internet but there is no information to set it. can u please t
Hello HAFEEZ, i am new in GPS module. i connected my GPS module to PC with baud rate 9600 and see the results on putty , hyper terminal. but results are not according to my location.. like time latitude longitude direction are not accurate... i try to see it internet but there is no information to set it. can u please tell...what is the prob
Hello Guys.... Today i m having a new problem... Here is my code:: #include <18f4550.h> #device ADC=10 #fuses HS, PLL5, CPUDIV1, NOWDT, NOPROTECT, BROWNOUT, NOLVP, PUT, NOMCLR #use delay(clock=20000000) #use rs232(baud=19200, xmit=PIN_C6, rcv=PIN_C7,parity=N,bits=8,ERRORS) #include void main() { float32 T , v
Hi all, Can i use usb to ttl or USB to Serial cable to upload the firmware to sim900, If any one know please let me know. I purchased a new sim900 device, here i am trying to enter MMS AT Commands in hyper terminal it reflying error so can i upload mms firmware? If yes which one is better.. please help me any one