Search Engine www.edaboard.com

# Inset Feed Patch Antenna

41 Threads found on edaboard.com: Inset Feed Patch Antenna

## Microstrip patch antenna not converging

Hi everyone, Building a microstrip patch antenna on HFSS. I used a wave port and de-embedded it to start on the beginning of the inset feed of the transmission line. During the solution, the convergence is not happening even though i have 30 passes with DS = 0.01. The results are very big like 5.7e+86 etc.. Any thoughts? (...)

## [Moved]: CST Studio: Two equilateral triangular patch antenna for 2.4 GHz

Howdy mates, These are two 2.4 GHz equilateral triangular patch antenna simulated by CST Studio. One has inset feeding, while the other has a coaxial feed. Hope they could be useful for someone. Attached please find the models. Have a good day Rodeoman

## [moved] formulae for patch antenna using inset feed

hello hope you are well, I am designing patch antenna using inset feed. I want to know the formulas how to find the width and length of feed? how much should be inset distance in patch and inset gap with patch (conductor)? Thanks

## Inset Feed Calculation Patch Antenna

I would like to calculate the inset feed dimensions for my patch antenna, Peak Impedance (impedance at edge) is 155.9072 +50.9807j. I rearrange the formula: 121564 with 50 ohms being the one you want, Zin(R). My question is, in the calculation, for the other impedance value Zin(0), should I use 155.9072, or the m

## Using srr in ground plane of auwb antenna

Wat should b d dimentions of tha srr in the ground plane of a uwb microstrip patch antenna so that its results could b enhanced than without any srr in the ground plane. Also where should b the inset feed placed.

## How to obtain the desired specs of rectangular patch antena using CST?

Looking your return loss, the question arises about feeding. What feeding you doing, u can start with inset feed or quaterwavelength feed. And, try matching the feed impedance with the edge impedance of patch.

## Relation of inset feed point and resonant frequency of an inset fed patch antenna

Hi all! I was simulating a simple inset fed patch antenna on Taconic TLC with Dk=3.2 and thickness of 0.79 mm at 2.45 GHz. While finding the inset feed position for optimum impedance match, what I observed was that the resonant frequency changes when I change the inset (...)

## my project is based on design of microstrip array antenna hey plz help me

can any one send the feed network for the 2X2 microstrip patch antenna with inset feed.plz help me out...:)

## inset feed width in microstrip patch antenna

plz can some one tell me how to calculate the "width of the inset feed in microstrip patch antenna" having dilectric constant 4.36 ,height of substrate is 1.5mm and frequency is 2.4835ghz...tell me the formula for this

## micro strip inset feed design for tooth like slot on patch

sir how we design inset feed for tooth like slot on patch antenna.if inset feed cross center of patch how we calculate input impedance..

## Microstrip patch antenna inset feed width -HFSS

Hi, We designed a microstrip patch antenna using HFSS having the following parameters shown in fig. 89522 In this fig, when the inset distance is varied slightly ie even by 0.001mm also, the impedance decreases drastically. This could be pretty dangerous when manufacturing the antenna is in question. Is there any soluti

## designina rectangular patch antenna

how to insert slots in the rectabgular patch ?wht are the basic required papmeters to locate the location of slots in rectangular patch near the inset feed ..?

## impedance maching in patch antenna

Hi How can I use interdigital capacitor for impedance matching in patch antenna.The antenna is feeding by transmission line. what's the best way for impedance maching in patch antenna?I wouldn't like to use inset feed technique.

## Inset feed not working on simulation

Did you tweak the length of the inset feed?

## microstrip single patch antenna bandwidth improvement

Hi, I am designing a single rectangular patch antenna . the substrate is Fr4 and its dielectric constant is 4.4. I have used inset feed for the antenna. The frequency is 2.4Ghz. I obtained the following results. My resonant frequency(Rf) is 2.399Ghz return loss @ Rf is 40 db There are many (...)

## design of rectangular array of patch antenna using ADS software

Hello Abprhe There is an equation for inset point,if you would like to do inset feed or you can do impedance matching technique,look up the equations in" antenna theory by balanis" Equations are explained in detail.microstrip antennas. There are many options for doing an array it depends whats your (...)

## single patch antenna design

Hi, I am designing a single rectangular patch antenna for 2.4Ghz. i am using inset feed. I used the std formulas available in Balanis to cal the length and width of rectangular patch. The length = 30mm, width=38mm, Er=4.4,height of substrate(fr4)=1.6mm. The feed width was 0.5mm. I (...)

## Inset characteristic of a microstrip patch antenna at 12.1 GHz on glass substrate

Let's assume that the inset gap length used by the questioner means the width of the inset gap, which is the dimension along the same direction as the patch width. One antenna textbook says that the inset gap length commonly is 3 times of the feed-line width. However, if the (...)

## Help with design of inset feed patch antenna

let me put this straight.. I have a patch antenna that I want to feed with a microstrip line. The output of my generator is at 50 Ohm. can someone tell me EXACTLY how to design the connection between the generator and the antenna?? I already calculated the value of all the parameter of the antenna, I just need

## help please,it's urgent: double inset feed patch antenna

Hi bvik, When you test one of the insets, is the other one loaded with the matched impedance? Can you show a drawing of the antenna? Regards Z