Search Engine www.edaboard.com

lm2596

Add Question

36 Threads found on edaboard.com: lm2596
I design a circuit of Modbus and GSM with two different regulators. Modbus need voltage >4.8 and GSM need 4 volt so i used 7805 (1Amp) with Max485 and atmega8 converter and lm2596 (3Amps) Adjustable regulator to power up GSM board . and input supply is 12V/2A adapter. when i use this circuit to read data from inverter and send data using http requ
this will do it tho' its BGA.. This is in to220... This one is easiest...adjust output to your 3v8... - - - Updated - - - here is a basic buck for you whi
Hello everyone how are you. I am working on a circuit that has a SIM800 module with an external L Shape antena. The module is powered by a lm2596 DC DC converter. The problem that I have is during the module registering phase to the network. It suddenly resets and start o ver again. But if I hold the antenna with my hand or if I place a finger ove
LM2576 (52KHz) or lm2596 (150KHz), which one is better for Raspberry Pi power supply (which needs a noise free 5V/2Amps supply from 12VDC (230VAC to 0-12V Transformer)). Only their difference is in PWM. will higher PWM give more noise free output ? Thanks in advance.
I believe you didn't read the lm2596 datsheet thoroughly and still less understood the reasoning behind the suggested capacitor and inductor values. The tables are based on a parameter "maximum input voltage" and "maximum input current". In case of doubt you'll use the largest inductor and capcitor value. It's always allowed to use a larger i
The power supply to the modem module is specified as 3.2 to 4.8 V. You surely don't want to supply 9 or 12 V directly to the module. The reference circuit in the hardware manual uses a lm2596-ADJ switching regulator in front of the module.
I have digital communication devices originally intended to operate from battery. - supply voltage 4V - supply current in standby about 1mA - supply current in full operation mode 100mA at 5ms, follow burst 2A at 0,5ms etc. - maximum allowable ripple 150mV This device is blocker 220uF tantalum capacitor. Power supply Requirements -Input v
Please critique my Buck converter layout (simple lm2596) Should I pour the entire bottom layer as ground and tie bottom to top layer ground with multiple vias, or split the bottom layer for best results? Thanks you for you comments.
You can use a switching regulator like lm2596 You can get a module from ebay for about a dollar 106612
well, I'm using a car batter to power up a monitor (230V) and a BBB at the same time. BBB is powered through a lm2596 switch mode regulator. (12V -> 5V) Monitor through a 100W inverter. (12V -> 230V) It seems like BBB cannot generate a video output when both share the same battery. :(
hey guys, I'm an undergrad in software engineering and I'm doing my final year project. I'm trying to power up a monitor and a Beaglebone Black from the car. I have used a 100W Inverter for the monitor and a lm2596 regulator for the BBB. And the lm2596 is a switch mode power regulator. Check diagram. 104981 But I d
Hello! I'm currently designing my first PCB and I already went way out of my skill level with the low space. I'm using lm2596 switching regulator circuit, with full circuit listed in my IC datasheet. It powers SIM908, which is using mostly 5mA current and peaks to max 2A. Input is 12V-15V from car battery. So here it is(apologies of my poor pa
You can use lm2596 switching regulator. The cost of a board from ebay is about $1 so you may as well buy a ready solution 101843 Note that you should avoid linear regulator solutions like LM7805 or LM317, they are inefficient and generate too much heat when the in/out level difference high.
search for "lm2596 5v" on ebay and it is soooo cheap that you better buy a ready made module than build it yourself. just my 2
A switching regulator would be the most efficient way with low heat dissipation, something like lm2596-3.3 or LM2576-3.3
Using buck converters as voltage inverters is addressed in an application note. There are stability caveats to be considered. Generally the method is working fine. I've implemented it in a number of commercial products with National/TI converters. lm2596 is a first generation simple switcher wi
Hello, I'm trying to design a 12v, 5V, 3A dual power supply based on the lm2596 voltage regulator. Now I need about 2A on both the 12V and the 5V rails. This is supposed to power a SATA HDD and a raspberry pi board. I've attached a schematic here and I was hoping you folks could tell me if it would work? Also can I use the 5V rail to power a raspbe
Go to ebay. Search lm2577, sort by price, and start looking around. Also do the same for lm2596. These $2 and $3 modules are cheaper than what you can get the parts for. They aren't generally quite 3A at 40V, but to give you an idea on similar. In fact search both 'step up' and then 'boost' with 'module' and 'converter' for both. In fact agai
What is the dropout voltage for a lm2596 DC to DC buck converter? for 5v 7805 voltage regulators i know that the output voltage drops around 6-7v depending on the regulator but what about buck converters? does it work in the same way? does it even have a "dropout voltage?" thanks You can see in datash
Hi all, I am using DC-DC converter lm2596 in buck mode to power up charging interface of a GSM module (SIM900D). The standard charging current of this module is around 650 mA . I am providing it 5.5 V (from lm2596) as Vchg. The regulator is perfectly providing required current when difference between input and output voltage is lower (upto Vin = 8