Search Engine www.edaboard.com

Pic hd44780 Lcd

Add Question

44 Threads found on edaboard.com: Pic hd44780 Lcd
Hello, bought pic programer(mikroProg) from mikroElektronika and i have some problems with lcd could you help me out? Im using pic16F628A and Hitachi hd44780 lcd. My code in C looks like this : sbit lcd_RS at RA0_bit; sbit lcd_EN at RA1_bit; sbit (...)
This is Multiple I2C lcd code. It is written using CCS C Compiler version 5.044. This si tested in Proteus and also Easypic v7 development board with 2 x 20x4 lcds. lcds should be hd44780 or compatible. I have used I2C lcds and I2C lcd modules from Banggood. I will soon (...)
I have got my 4x20 lcd working so I can write data to it but I cannot succesfully read the busy flag. This is a 3.3v pic so I am using open drain outputs and 5v tollerant inputs. After scoping the Enable and D7 lines I can see the D7 level is low when it should be reading but my routine (lcd_status) always returns 1. I have been trying (...)
Hi, I want to get value of Temperature from temperature sensor and by using ADC of pic I want to send it to other pic U controller using XBee module.please tell me how to interface pic with Xbee.I need your help. my circuit for temperature sensor is this. 101935
hi im trying to use lcd module with i2c driver and i cant understand how to program if someone have a sample code plz share 97270
Hi everyone i'm trying to use hd44780-based Character-lcd(4line20character) . I found some material from some forums but couldn't make it. If you check my software steps i appreciate it: 1st: I designate port configurations #define RS PORTA,0 #define RW PORTA,1 #define E PORTA,2 #define lcd_DATA PORTB #def
I assume you're using an hd44780 based lcd, as I could understand from other posts of yours. Before reading you must enable the pic to read data from the lcd data pins, so change the TRIS registers values to 1 for the lcd pins (except for En, RS, and RW). Then set RW to 1 (READ) - the lcd (...)
What a union does is let the compiler know that you want to be able to access the same location in memory in more than one way. So, for a simple example, here's how I do this in my hd44780 lcd code: union { struct { unsigned bit0: 1; unsig
//Project: lcd hd44780 Lesson, lcd 16X2 Example //Programmer: Shahrulnizam Mat Rejab //pic: pic16F877A, pic16F887, pic18F4550 //Crystal Frequency: 20MHz //Compiler: HI-TECH C for pic10/12/16 V9.83, pic18 V9.65 //Last Modified: 31 (...)
If you using C Language, can refer here lcd hd44780. The header here.
The hd44780 chipset offers either 8-bit or 4-bit data I/O, not 16-bit. The interface and coding method is similar to utilizing the device with an 8-bit pic. There are numerous hd44780 compatible lcd libraries available. Are you coding in C or Assembly Language? If C, what compiler are you using? BigDog
You can create header file, it's extension is .h. Then, in the C code, you can include the File Name.h. Ex, code for lcd hd44780, the with the header file. Beginner now, not know how the lcd operation, just use the function/header created by m
lcd Lesson and Header File.
The pic being used is: pic16F877A lcd beind used is: NHD‐0216KZ‐FSW‐GBW The objective is to get the lcd to display the following message, "Bananas $0.49/lb" - for 5 seconds, followed by, "WOW!" - which is centered on the display and blinking at a rate of once per second for 3 seconds (i.e. 500ms
Hey guys, I need a little help displaying the time on a hd44780 lcd. Compiling on pic basic Pro. There are two of us having the same issue. Below is the code I used. The display is Time=00:00:00 Date=00:00:00 Any suggestions would be helpful, not very good at these things. I will owe you a burrito if we can get her running. (...)
I should reset power of both pic and lcd to bring lcd back to normal. Does it work? I assume that you are using an industry standard Hitachi hd44780 compatible lcd. The dataheet has detailed instructions how to perform a reset without cycling the lcd power.
Dear frnz I want to design a project using pic24f series and 16 x 2 lcd. My problem is that pic 24f series work on 3.3 v operating voltage while lcd needs 5 v to operate .i want to connect many periperals like pendrive etc. which also operate on 5 v. how to solve this problem? please help. thanku lats
Hello, Ive been reading up on how to interface an lcd to a pic for a few days now but am still quite confused.. I read from this link: lcd Tutorial for interfacing with Microcontrollers: Introduction : 8051 Microcontroller Projects AVR pic Projects Tutorials Ebooks Libraries codes
There are sample codes available with Hitech C compiler for lcd demo..but it is written over there tat code works wid hd44780 lcd controller. I am using JHD162A whether tat same code can work
I hooked up a Hitachi hd44780 based 2x16 lcd with pic18F2420. Now on the bootup, I should see boxes in the top row (Typical for a hd44780 based lcd). But what I see is 8 boxes in top row and 8 boxes in Bottom row. Is the lcd Blown or something else is wrong? I have (...)