Search Engine www.edaboard.com

Pic Pro

Add Question

Are you looking for?:
pro pic , pic pro and , pic pro plus , pro pic
356 Threads found on edaboard.com: Pic Pro
I powered it from 1st MCLR pin, put 8mhz oscillator with capacitors into 13th and 14th pin, connected led to 19th pin and led is not blinking. ??? MCLR/VPP is not the power pin. Must supply VDD pins 11 and 32. Please show your complete circuit. To simplify the test setup, you can run the pic from internal oscillator. One
hi all, i have written simple code to check comparator output, but nothing is happening i have used micro c pro for pic for writing program i have disabled PORTB A to D conversion in config bit settings. here is my program void main() { osccon=0x7c; // select 8Mhz internal oscillator //CONFIG6H.bit1=0; (...)
Okay, so i tried to interface pic16f722A with LM016L LCD. i had wrote the C-code for initializing (LCD) and displaying characters on LCD. Somehow i got stuck when i simulated the program in proteus. The problems are as follows: 1)When i transfer X number of characters, it just shows (X-1) number of characters, ignoring (...)
Do you have any experience with new version of GLCD v2.0? I had a design working few years ago. Recently I bough this 135753 new GLCD for that design. But When I connected it, it work improperly. Almost no output and noise in the Display. Here you can see that this new version has PSB and NC (No connection May be) pins rathe
Hi I have problem with strcat() Find attached mikroC pro pic project and proteus simulation file. Press A button and it will show "Set frequency" Frequency will be 100.00MHz Now use B or C button to decrement or increment the value and then make again value 100 then it shows 100.0MHz instead (...)
I am not getting random numbers between 0 and 9. I am using pic16C73B and mikroC pro pic. srand(32757); random = 32757 - rand(); Edit: Found the solution. random = rand() % 10;
Which GSM modem ? SIM900 ? Where is AT+CNMI=.... command for new SMS notification ? UART1Read() returns only a byte. What is the Crystal frequency ? I can give you the code but not for 16F877A because it has less RAM and mikroC pro pic doesn't generate bank switching code. To receive AT+CMGR response you need a big array
I'm trying to connect a pic16F877A to program it in MPLAB X IDE, but I'm getting an error about target device ID. My breadboard: MPLAB X: Currently loaded firmware on pickit 3 Firmware Suite Version.....01.43.35 Firmware type..............Midrange programmer to target
Hello everyone For my new project i am using pic16F873A MCU. The intention of my project is to monitor 4 analog input values and make the control signals as per the read analog values. The IDE i am using is MikroC pro for pic. The program is working perfectly in the software and i (...)
my mikroC software seems to be outdated. V6.0.0 can anyone help to convert this code to hex file please. need it badly. thanks. // VARIABLES char second = 0; char second_old = 0; char minute = 0; char minute_ten = 0; char minute_one = 0; char hour = 0; char hour_ten = 0; char hour_one = 0; char counter_1=0; char count
Hi! I am working at transmit ecg waves to android mobile phone via bluetooth .First I try application that communation the bluetooth module and pic16f877 appliction is that count from1 to 100 in for loop on microc pro for pic program . I try this.I write the android mobile screen word 'a' that transmit via bluetooth .But I m
hi all, i have tried so much but pic 18F458 is not reading RTC DS1307, PLz help me oscillator -HS 20Mhz complier-micro c pro for pic here is code // LCD module connections sbit LCD_RS at RB7_bit; sbit LCD_EN at RB6_bit; sbit LCD_D4 at RB5_bit; sbit LCD_D5 at RB4_bit; sbit LCD_D6 at RB3_bit; sbit LCD_D7 at RB2_bit; sbit LCD_RS_Dire
hi all, i have tried so much but pic 18F458 is not reading RTC DS1307, PLz help me oscillator -HS 20Mhz complier-micro c pro for pic here is code // LCD module connections sbit LCD_RS at RB7_bit; sbit LCD_EN at RB6_bit; sbit LCD_D4 at RB5_bit; sbit LCD_D5 at RB4_bit; sbit LCD_D6 at RB3_bit; sbit LCD_D7 at RB2_bit; sbit LCD_RS_Dire
Hi-Tech picC project Not Compiling I have attached the project. Code is correct because I have ported mikroC pro pic Code to Hi-Tech picC. I am using Lite version of the Hi-Tech picC Compiler. I am using the last version of the MPLAB and Compiler. Please see the (...)
LEDs at PORTD are blinking about after 3 seconds Is there problem with oscillator selection? pic 18F4550 MikroC pro Code: void main() { TRISD = 0x00; while(1) { PORTD = 0xFF; Delay_ms(100); PORTD = 0x00; Delay_ms(100); } } 127422
Hello! I'm using mikroC pro for pic and proteus 8. here's the header and source files and the circuit 126497 My code works perfectly when i comment these 6 lines in programme.c (from line 93 to line 98): Lcd_Out(1,2,"OPERATION"); Lcd_Out(2,8,"ACHIVED"); Delay_ms(5000); Lcd_Cmd(_LCD_CLEAR); Lcd_Out(1,2,"Press START (...)
ConnectEve Analog Clock and progressBar project. i have used this TFT. The Clock is made using FT800 mikroC pro pic32 Library. MCU used is pic32MX795F512L at 80 MHz but even pic or AVR can do the job with ConnectEve. VisualTFT is used to make the Clock project. (...)
Hi guys I'm facing problem interfacing serial dac with picf2550. i tried simulation, it works but hardware is not working. Actually I'm trying to generate modefied sine and cos waves. I think there might be something I'm doing wrong with configuration bits or may be SPI is different. Need suggestion. P.S: i tried the same code with a few change
im working on project (pic16F1705) and i try to understand the Convesion library, i used an example provided in the exemple folder. /* * project name: Conversions * Copyright: (c) Mikroelektronika, 2008. */ char res_ch; int res_int; char txt; void main() { char txt1 = " mikroelektronika "; (...)
Thanks Mr pic programmer and. Ajaya Kumar for your time and consideration. Also Please tell me the Full name of keil IDE