Search Engine www.edaboard.com

Proteus Isis

Add Question

299 Threads found on edaboard.com: Proteus Isis
Hello! I have a question regarding isis proteus. I want to modify the existing LM35 so that the output is 250mV + 7.0mV/degree instead of a flat 10mV/degree. I was thinking of modifying the SPICE model? Design: LM35.pdsprj Doc. no.: Revision: Author: Created: 27/11/2012 Modified: 27/11/2012 *PROP
I'm looking for the RJ45 connector in proteus and i cant find it, does anyone have a library that i can use? thanks for any help in advance.
Hi, I would like to know how to import an IGBT (IXYH20N120C3D1) into proteus isis. All the examples for importing parts into proteus which I have found on the Web, relate to either NPNs, PNPs, Mosfets or ICs. The best idea I have at the moment is to treat the IGBT which I wish to import, as a 3 pin IC. There are already a number of IGBTs in (...)
It is just a warning and can be ignored since you know that the slave, when configured, will change the SCK pin to an input to be driven by master. It is just a simulation and proteus may not take that into account.
Hi, I am trying to figure out how I can make a package for a connector device I have made where only two of the four pins are present in the pcb package. Basically I have a new schematic part I have made to represent both sides of a PCB wire to board connector - one side sits on the PCB and connects to other parts of the circuit board, whils
Few days back, I imported my Graphic LCD project in proteus 8.4 sp0 and its giving the same error, logic contention and doesn’t work for me. I am worried that why it is not working as the last time it was working. Then I installed old version of proteus 7.11 and open the same project in that, and it started working again. So i think there is
I am designing an automatic voltage regulator (AVR) for a generator. The isis file and image of simulation is attached. The output of AVR should be 70-80V DC accross diode D1. Problem: The full-wave bridge rectifier works fine independently but gives zero output when it is connected to the rest of the circuit. The output of bridge should be 26V
Hello, I am designing an automatic voltage regulator (AVR) for a generator. Attached is the isis file and simulation of the circuit. Problem: The full wave bridge rectifier works fine independently but gives zero output when connected to rest of circuit. The output of bridge should be 26V DC at capacitor C1. The output of AVR should be 70-80V
Hello, I am designing an automatic voltage regulator (AVR) for a generator. Attached is the isis file and simulation of the circuit. Problem: The full wave bridge rectifier works fine independently but gives zero output when connected to rest of circuit. The output of bridge should be 26V DC at capacitor C1. The output of AVR should be 70-80V
Hi how can i make component in isis proteus , its TSOP 1738 I have watch most of videos on proteus site and youtube videos as "make a component in isis proteus"but i fail. anyone has good link video , or document .. so i can make tsop 1738 with success thanks a lot
Hello! First, I apologize for my bad English. I am designed a device in isis as shown in the image I have assigned to it a package obrazki
Hi, I am trying to charge and discharge an inductor in proteus isis but the result does not seem to be right. Why? Please help me. Thank you. 126839
Hi everyone, I am going to make simulations about cell balancing circuits for lithium-ion batteries. I want to use proteus isis for simulation but I could not find cells that I can set some spesifications like capacity of cell. If someone know anything about it, please let me know. By the way, ıf you know a better simulation program for cell
i need to built an IR controlled switch, i want to simulate my proposed circuit in proteus. so that i found IR transmitter in proteus isis 8.1 but couldn't find IR receiver there. any help please
Hello All, I'm currently building an interface to HD44780 LCD, and needs PWM to drive the backlight. For some electrical rules on PCB, i can only set PWM at P1A/RC5, but i'm unable to get it done, even with isis proteus simulation, its outputs nothing. Here is the code for the PWM for lowest possible frequency, at 48MHz fosc: void Ini
1) can i import microprocessors IDE, BSDL Model or IBIS Model to proteus isis to simulate them? will it work? 2) is there any supplier giving proteus spice model to direct import to proteus library? if yes, please state the supplier name, model types and how to import them. thanks.
Hi there, I?m looking for proteus isis simulation model for i.MX233 processor. Based on website, only IBIS model available. I know that IBIS model cannot be simulated in proteus isis. The objective is to simulate the processor model in proteus isis before starting layout. is there (...)
Hello Everyone, i have created a custom nRF51 bluetooth component and i added to the exisiting library part followed by i created a simple schematic using LED then in the simulation part it is showing duplicate part reference i dont understand what is this error? and i also when i edit my custom component i am not able to program path, and cryst
Hi all, Is there a way of removing all wires on the pcb layout on ARES? I did a auto routing and then saved it and closed the application so I cant Ctrl z. Thank you, Owen
So if I add a top and bottom copper plane are they considered layers? No, you'll add copper planes on two inner layers. Apparently, proteus Ares has a fixed set of 14 inner layers which are enabled and visible by default. I would deselect all but "inner 1" and "inner 2" and place GND and VCC planes on it.