Search Engine www.edaboard.com

# Pwm Wave Generation

34 Threads found on edaboard.com: Pwm Wave Generation

## Sine Wave generation using PWM and PIC16F72

At the output i am using 1kOhm and 102 to filter. 102 means 1 nF? 1k*1nF = 1?s time constant = low pass cut off frequency 160 kHz. How should it filter 20 kHz pwm? Secondly, why are you stepping through the sine table up and down alternatingly? Makes no sense. A sine full cycle should be repeated continuously, either up- or downw

## Easy Sine Wave Generation with PIC micro-controller

Very useful thread for many electronics hobbyists like me. The topology presented using 2 CCP module of PIC. I think it will be pertinent here to request for a topology of generating sine wave using software pwm i.e. without CCP module of PIC.

## Multilevel PWM Generation for Class D Amplifier

Hi, I need to generate a 3 level pwm for a Class D amplifier in full-bridge. I've been searching about this for some time but I haven't been able to find any usefull circuit or IC to do this. Can anyone help me with this? Thanks!

## Three phase sine wave generation using PWM

But here the step size of 1Hz is possible and now I want the step size of 0.1Hz. I presume you are referring to the "Delta_Phase variable" calculation? The output frequency doesn't have exactly 1 Hz resolution, it's about 0.3 Hz for the given pwm frequency and phase generation scheme and your Hz number will be rounded down to the

## Can we use the sine wave generated by IP cores for PWM generation in Verilog?

I want to use pwm using sine triangle generation. If I generate sine waves using Ip cores can that sine wave be instantiated in another module which generates the triangle waves? I mean without writing a test bench can we connect these signals in Verilog?

## AVR PWM wave generation in codevision

Hi guys, I woud like to produce a pulse with 200 HZ frequency and 0.07 duty cycle, so I used timer2 of atmega32 in FAST pwm mode. For this purpose, I used external crystal 4MHZ, and Prescale 128 (FOR 200Hz). basis on fpwm=crystal/(prescale*(256-tcnt)) formula, I computed 100 (0x64) for TCNT2, For duty cycle 0.07, according to dutycycle=ocr2/(256-tc

## pwm pure sine wave generator

I want to know the various ICs that can be used to generate pwm sine wave. I was able to get one on google but not with much design support. HT1112 IC. Please help me out. I dont really want to deal with programming microcontrollers as I do know they can be used. if you are looking for a sine wave generator DDS chips

## designing ckt in proteus for buck converter by use of tl494

hey,i didn,t find any ckt to generate a pwm wave generation ckt for simple buck converter without using any transformer. i need a 10khz wave generation to be used for converter control. can anybody help help me...please

## PWM wave generation........

hi guys,i have a problem regarding pwm wave generation.i want to generate a 770hz pwm with 10%duty cycle on timer 2(atmega8) ,crystl is my TCNT value s 0x5D,and OCR is 0x6D according to my proteus shows generated signal is pls help me finding the problem.thnx...

## PWM Generation fir boost converter using pi and traingular

hi i need a VHDL code for pwm generation for boost converter..i want to generate a pwm by comparing a output of pi controller with triangular wave(counter) plz help me in this..m complete new to vhdl/.

## 4 square wave generation using PIC18F4520

Hello I been have been reading the PIC18F4520 datasheet regarding the CCP section. For some reason i cant seem to understand how to start generation of pwm. I am highly confused. I want to generate 4 square waves of same frequency and phase shifted by 90 to drive MOSFETS in a synchronous buck converter. The pwms must be (...)

## Cosine Wave generation in ARM microcontroller

anne, In order to avoid exorbitant ALU calculation, I performed this task in an 8-bit PIC microcontroller just accessing a look-up table, and loading this value into a pwm duty-cicle module. const unsigned int8 Duty0 = {7,15,23,31,38,46,53,61,68,75,82,88,95,101,107,113,118,123,128,133,137,141,144,147,150,153,155,156,158,159,159,

## compare mode for pwm generation

I want to generate three pwm signals in pic16f73. we can generate two pwm signals using ccp1,ccp2 module that i know.but i have to generate 3 pwm signals from three pins.The first pwm signal is +ve half of a sine wave and 10ms gap.the next is +ve half and 10ms gap.if we mix the two signals we have to get an (...)

## Generation of PWM using External Interrupts and Timers on a scope...

Hello, I'm trying to generate a continuous pwm wave on a scope from the C8051F330 micro-controller using external interrupts and timers only. I have put up a piece of code. Could anybody please look at it and spot any mistake/mistakes that I've been doing which is eventually restricting the output...? The code is as follows: //-------

## DC/AC 50-kHz Inverter PWM: Sine modulation or squared wave?

Hi folks, I am designing an AC/AC converter that provides a 50-kHz 230-V AC wave. 230-Vac main supplies the converter, which is composed by three blocks: an AC/DC rectifier (diode bridge), a DC/DC boost converter, and the DC/AC 50-kHz inverter. My question is: which pwm mode should I use? Either a sine modulating wave (switching (...)

## PWM Three phase inverter

HI rikotech8. For 3 phase sine wave inverter it needs 6 complementary sine modulated output with deadtime generation. which is already implemented in hardware of 18F2431 architecture. You just have to set corresponding SFR's and a sine lookup table which will fed sine modulated pwm duty values to the duty register 120 degree apart to other.

## pwm using AT89C51 MICROCONTROLLER

hello everyone, I have generated a pwm signal with 50% duty cycle using the timer concept but i don't know why I am getting a 60 degrees phase shift in the output wave so that if I compare with a standard square wave from a square wave generator my wave is keep on shifting may I know the reason...... (...)

## Can we Generate two PWM waves with a phase difference of 180degrees using ATmega16??

Hi everyone, Can we generate two pwm waves with a phase difference of 180degrees using AtMega16/32 MCU?? If yes, please explain how to do it. Else suggest any other AVR Micro-controller for the same purpose.

## IR2184 problems in buck

Hi everyone...I am buliding a buck convertor using IR2184. Igbt i am using is MG300H1UL1. But i am not geting any output. I am generating pwm from microcontroller and that is coming on IN pin.And i have grounded the SD pin.can someone please tell me where i am wrong..All other pins are connected according to datasheet. www.datasheetcatalo

## c language coding for square wave generation

Your basic requirements are the generation of Pulse Width Modulation (pwm), of which the defacto square wave is pwm with a 50% duty cycle, half the period of the waveform ON and the other half OFF. There are primarily two ways of generating pwm, through software/bit-banging or using a (...)