Search Engine

rs232 And Vhdl

Add Question

20 Threads found on rs232 And Vhdl
I want to implement rs232 receiver in vhdl with FPGA Altera DE1. I have try to write some code but I know that is not good, my main problem is that I dont know how to get an indictaion that new data(serial data) is actually what I did is to move each bit of the serial data to the out parallel data (8 bits) every rising edge of the main
Hi.I am so sorry because of my poor English speaking! I am trying to write a simple code in vhdl for rs232 to receive data through a wire as you is my code! something is wrong! please help me to solve this challenge!thanks :) 99316 as you can see,bit_cnt pulsed twice!!!!!why? and number of "get" state must
Hi everyone! I am very new in vhdl and I need some help with the asignment I have to do. I want to send a character with hyper terminal to Spartan 3E board via rs232 and show its ASCII code on 8 LEDs. I have already implemented UART Receiver but now I don't know what else should I do. Do I have to make a new FSM to (...)
I have a problem with rs232 transmission. It doesn't work even when i send the first, start frame($55). Next frame $3x choses a led and the last one turns it on/off. I cant even turn on a led when i get start frame. I cant find any mistakes in a code. Maybe You will find something or give some advice. I enclose code with a problematic part. [COD
some issues are apparent: 1.) rs232 is lsb first, so "z" will come up as 0 0101 1110 1. 2.) you appear to transmit "M" lsb first (correct), but the start/stop bits are swapped (incorrect). eg, x1(0) = '1' and x1(9) = '0'. Thus the framing will be incorrect. the receiver may see 11001001 as the data byte, which would be an extended ascii charac
Hello, I am using my FPGA(virtex-6) kit for the project, project is rs232 to Ethernet converter, 1) i ll write a code for the rs232/434 and dump my code in FPGA then i need to transfer the data by Ethernet to other device or PC. 2) vice versa the data which is coming from the PC or device from the ethernet port need to be stored in (...)
Please look at They have rs232 as well as ethernet mac core.
We are trying to do some homework making a rs232 transmitter... This is what we made so far and there is a lot of faults it it.. but we don't know what. We think its something with the way we written the states. Please rewrite it to some useful syntax this is what we made so far library IEEE; use IEEE.STD_LOGIC_1164.ALL; us
hello everyone, i had written uart receiver module and baud generator module for baudrate:9600 bps in vhdl. This code is working properly for all 1 digit values. Now i want to send a text file containing datas such as eg: 123 56 234 175 34 100 how do i send this through rs232 to fpga??? Thank you all in (...)
Not quite sure what the problem is, but since you mention rs232 ... Check out this uart module on fpga4fun. It's explained pretty well, and more importantly, it actually worked the first time around! Just change clock frequency and baud rate parameters and you are good to go! good luck!
hi all, i need for a project to decode characters sent to rs232 Receiver module the RS 232 receiver will feed its data to the LCD display and that will be on spartan 3A . i have the rs232 Receiver module done but what i am missing is the part related to the LCD display as i want one and i hope it is in (...)
Hi, im really new to this project and i dont know where to start. All i know is that i could use the hyperterminal for me to send data towards the FPGA... but i dont know how to do it... also the hardware stuff for the connection between the PC and FPGA... what i want is to make a simple project that sends data only towards the FPGA so that i could
Hello, I assign both outputs and inputs of my uart vhdl codes to the 9 pins of that correct?? In the entity part of the uart vhdl code below, rx_data_out and tx_data_in are 8 bits width.I don't know how to assign them with the pin of rs232..anyone can help me?? entity uart_serial is port( -- (...)
I have a Xilinx Spartan-3E and what i want to do is this: Press a button ex. East Button on the board and send a signal eg. "00101100" to a device on the other end of Spartans rs232 port. Like when i press the button and the leds are on i want to send this signal over the serial port lets say to a PC on the other end. (...)
refer rs232 in get verilog source code there
Hello! I am doing my final project in computer engineering and I need to connect a CMU cam into Ethernet. I was thinking of building a hardware using vhdl which will transfer between the Camera's serial port to Ethernet (and the opposite of course). Does anyone know where I could find such code? Thanks! Lior.
I am in need of source code of vhdl OF -- PS/2 and rs232 --Protocal!! if you have it ,or you know how to program it in vhdl , please help me!:| thank you very much!:D
i have spartan3 fpga starter kit from xillinx i want vhdl or verilog code to interface with ps/2 and serial (rs232) thanks for any help
Doing Complete calculator in vhdl wont turn out to be economical design. What you can do is you need to write / use some 8 bit vhdl CPU to do the job. Using this cpu you can interface keyboard and display to it. and use it for doing calculations also. 8051 core in vhdl is available you can use it. For (...)
Would anyone share the rs232 vhdl code ? If you have rs232 test program , please share. Thanks a lot.