Search Engine www.edaboard.com

36 Threads found on edaboard.com: Sms Hyper Terminal
The previous answer +CPMS: (),(),() clarifies, that the mobile does not allow any selection of preferred sms message storage. Obviously "ME" is not a member of "()". :D
Hello, I am doing a project, I have to send and receive sms using microcontroller. I am using AT89s52 microcontroller and nokia 6610i mobile phone. I have successfully sent and red sms from hyper terminal of PC. So nokia 6610i supports required at commands. Then I cut the serial data cable (DUK 50) of nokia (...)
im using PIC18F452 @ 20M and Siemens M55 to send and receive sms and calls, and it works gr8 but.. every time when phone is ringing, or call is active, all messages (at-commands)that mcu gets from phone is garbage. Phone sends them as it should(checked with hyper-terminal and DockLight), but somehow mcu gets only garbage. Can anyone help (...)
hi.. every body...... need help for my nokia 6600. i want to send sms from pc using at commands.phone is connected via bluetooth to pc. serial port connection with pc blue tooth device is established. when i type "at" in hyper terminal it returns nthing.(no "error" or "ok"). i also installed pc suite 4 nokia 6600 but no luck. help me (...)
hi iam using max232 to connect a pic16f877a to a nokia 6610 dku5 serial cablecable ,to send and recieve sms using at+commands. i have connected the max232 rx,tx correctly since i have tested the pic by connecting it with the pc ,using hyper terminal and send, receive work fine. and i have tested the cell too with the (...)
hi all , ihave problem with my project i making sms remote controller i connect the mobile sony ericsson (T290i) with (atmega8535) micro controller the controller send AT COMMAND to hyper terminal correctly but my problem is : no response when connecting uc to mobile it might be not matching in volt i use max 232 please i want the (...)
Hello, Try change to "text mode" AT+CMGF=1 Then read the sms 1 again! AT+CMGR=1 I Hope this solve your problem! Bye.
I have written a code for a sms controller. The code works perfectly well in hyper terminal, but when connected with SE T630, it doesn't seem to work at all. I found out that the main reason was the SERIN2 part, if i had that part remove, the code can be run on SE T630. But that only makes my communication one way, from controller to T630, (...)
That would mean that your phone cannot support sms at commands. Try to send "AT+CMGL=?" if it still replies "ERROR" or tyr agian sending "AT+CMGS=?" if it returns OK
Hello there...i need a smal help.... i m connecting my mobile with with PC using serial cable... i have also installed the drivers of the cable...and after making connection of hyper terminal with phone i m not able to see the commands i typed on the hyper terminal window...can any body tell me what is the problem... thanks...
hi firends.I have tried send sms by hyper terminal from siemens c55 cellphone and I wanna do it by pic16f876.I have writed this code.but it havent send sms it right?and my shematic is here ( ) is it right too? plz help me #include <16f876.h> #fuses HS,NOWDT,NOPROT
It's very easy:D Maybe a good link below could help you:
please i need a help on interfacing nokia 3200 using hyper terminal as an example i am using serial cable"f-bus" and i want to access the gsm modem of the mobile to read and and send sms,this is a vital issue in a graduation project i am on. the problem is that the computer fail to connect to the modem,i mean it can't go in a connection (...)
please i need a help on interfacing nokia 3200 using hyper terminal as an example i am using serial cable"f-bus" and i want to access the gsm modem of the mobile to read and and send sms,this is a vital issue in a graduation project i am on. the problem is that the computer fail to connect to the modem,i mean it can't go in a connection (...)
hi..i'm using t610 SE phone to communicate with microC either atmel 89c51 or pic 16f84 . before that i need to test the phone with pc using hyper terminal but i can't find a serial cable for this phone ...does anyone can tell me the pin configuration and do i need to use a max 232 ??
Hello, I have a GSM Modem, I used it for sms only. I checked it using hyper terminal and it works very well. I did make a circuit with 89c51 and simple program to send sms but it works some times and some time not. Any one know what is the problem. Thanks,