Search Engine www.edaboard.com

Standard Ipc

Add Question

70 Threads found on edaboard.com: Standard Ipc
I am looking for ipc standard document for PCB component designators , as per my knowledge ipc-2612 is referred for this purpose but I found hardly two pages of this document online so can any one send some link?
In most cases, assembly houses will assemble PCB's using ipc-A-610 as a standard for quality control. In ipc-A-610, three classes are defined; Class 1 Class 2 Class 3 This standard does not define the distance between to components but defines the allowable overhang of a component. This allowable overhang de
Hi, Can anyone please tell me the standard grid size (mm) for a typical analog layout. Thanks & Regards.
There is a standard for "Land Pattern Naming Conventions". it is called ipc-7351-B. And there is a naming convention for the footprint of a switch in it. You can use 'Google' to find this naming convention. regards
This is a tool to help you make footprints that are compliant to ipc-7351, much better to learn and follow what is now pretty much the industry standard in footprint design, so you are not searching libraries but getting an application that will do a lot of the mundane work for you in designing PCB footprints.
It looks like a very standard QFN 7x7...
Hi All, Need footprint creation standard documents for Flex type layouts, we have standard document(ipc -7351B) for rigid type boards, but no inputs found for flex type boards. also need through hole standard documents for inductor, capacitor, resistors,... if any found. thanks for advance, by karthik
What do you mean Mil standards licence? please clarify. As to Mil standard design, like most PCB design a lot of it is now covered by ipc standards... Basically both design and assembly should be to class 3 standard.... Search for ipc class 3
Most modern components are hard metric, the de-facto standard for SMD components (ipc-7351) is metric based, all mechanical design is metric, so it makes common sense to layout PCBs in metric...I have done for years.
Hi, Best is to go to the chip manufacturer's homepage ( if not in the datasheet) and find it's pcb layout recommendations. Or go for IEC standards. Klaus
Required pin distance is a matter of applicable overvoltage category. If you review Phoenix Contact datasheets, you'll notice that the 5 mm connectors are qualified for 250 V working voltage, although they can be used for 400 V interphase voltage according to some standards. For 400 V, you better use 7.5 mm connector families.
Hi, ipc-2221 standard talks about annular rings for plated through holes. It mentions three types, viz. 1) External Supported 2) External Unsupported 3) Internal Supported I understand that Internal/External means it is on internal/external layer. But what is the difference between supported and unsupported annular rings?
For your info, a list of ALL the major PCB related ipc specs, should be in this lot somewhere: 1601: Printed Board Handling and Storage Guidelines 2141A: Design Guide for High-Speed Controlled Impedance Circuit Boards 2152: standard for Determining Current Carrying Capacity in Printed Board Design 2221A: Generic standard on Printed Board (...)
If you want a standard then use:- ipc-2612 ipc-2612-1
HI every one, right now i am arranging Through hole footprints so i like to arrange in ipc standard,which ipc standard need to follow for Through hole components and Naming for Through hole also ..(IN ipc-7351 Land Pattern Naming Convention is available like that i need Naming convention for Through hole (...)
A list of the basic specs for PCB design fabrication and assembly: 1601: Printed Board Handling and Storage Guidelines 2141A: Design Guide for High-Speed Controlled Impedance Circuit Boards 2152: standard for Determining Current Carrying Capacity in Printed Board Design 2221A: Generic standard on Printed Board Design 2222A: Sectional Design Sta
as the topic says...we have recently sent in a board for manufacturing at this shop in Italy because of its high complexity , and they told us it is easy task for them, and turned out everything was all right. there is just one little thing...the board is 6.4mm thick, and with high aspect ratio meaning the board is thick enough but the via needs
Most people I know who do PCB design (and I know a few) use the Saturn Toolkit and have it on their desktop, If you are going to do PCb design I would reccomend you download it and use it. Temp rise above ambient, I use 10 degrees to play safe. But for commercial you can use 20 deg C. ipc-2152 is the standard for current capacity.
hi , first thing footprint are viewed in PCB editor only (choose file location and then select .dra format ) footprint name is depends on ipc standard ipc-7351 but some of company not following this standard and one more thing is 400,600 is may be value
Biggest driver is mobile devices. 6 billion discrete compnents are placed every day... Join the ipc and each year you can read: "World PCB Production Report for the Year 20xx" published in July each year. Here is a rough breakdown of World Production by Board Type from the last release: standard Multi-Layer 38.0% HDI Microvia 14.6% IC Sub