Search Engine www.edaboard.com

Uart Avr

Add Question

114 Threads found on edaboard.com: Uart Avr
Hi, What code do you need? Gprs modules often communicate via uart, but it could be any other interface, too. Code for sending and receiving data with a uart? Or do you need to know the GPRS commands? How do you want to process the GPRS data? Storing in memory, showing on a display, transmitting to a PC? Please give detailed descriptions. Don't
hello friend, i was used an ic atemag32,in it i programmed and it work well for adc,uart,ext interrupt,timer all...but some days before i bought 3 new atmega32 ics,i placed it in my old board and burned the same old working program, but the adc is not working in new 3 ics...i am using avr studio complier.then i compired the fuse settings of worki
I have some problem with uart communication bettwin two avr micro-controller,I am using Microbasci For avr and two side code are here: ***Transmitter Side:*** program MyProject ''symbol Key0 = PORTB.0 ''symbol Key1 = PORTB.1 symbol MYDELAY = delay_ms(100000) dim (...)
It's highly unrecommended to build a software serial port. The serial-port signals are over-sampled and require a percise monitoring of the signal to cancel-out any potential noise. I would suggest reconsidering the MCU used if you don't have enough serial ports for the project. You could also use a I2C to uart converter (for example SC18IM700). T
but now simulation Works properly you mean simulation works with lcd display but not at real hardware? just a thought why spi direct uart is easy to implement.and you can check the spi logic with logic analyzer.
It is not related to compiler version problem i think you need to set TXC bit manually while you are using simulator. In real time it sets automatically for successful data transfer, so if you set your TXC bit I think you will able to run your uart simulation
If the camera driver board actually does uart communication with LVDS level (not sure about that), you can use a 3.3V LVDS driver/receiver IC like SN65LVDS179.
read_adc=x; putchar(x); Meaned this? x=read_adc();putchar(x); avr ADC outputs 10-Bit data, so the code isn't particularly useful. And you want to write the data to USB rather than uart, where is the data sent by putchar()? If you send binary data over USB through virtual COM port protocol, you usually want some kind
Please refer to this.
This colour sensor does not use uart it necessary in your project to use a uart based colour sensor or you can use something
I have been designing atmega 8 based usb to uart conversion using v usb and avr cdc 232. The whole circuit seems ok but its not detected in by the computer. It just says USB device not recognized. Here's the description of the project( ).Any help please I us
Hi, again: Asking for fast help, but giving no details is resulting in no answers.. Do You Have any Idea how should I connect avr and optocoupler Pins? google for "atmega uart optocoupler" then decide what else you want to know. Should I connect a RC circuit for RESET pin? look into datasheet
Section 6.6 in the user manual explains how you can setup and use uart in codevision - - - Updated - - - You can also take a look it the Two USARTs and LCD example that can be found www.hpinfo
You'll think about suitable debugging means for your problem. Hardware means: - an oscilloscope to monitor the Rx and Tx data - an uart spy adapter that taps Rx and Tx data and send it to a PC, at best two RS232 channels and Docklight software Software means: - avr in system debugger Regarding possible baudrate problems. The usual way is to
I have to receive data from uart and turn on Relays but they are not functioning as expected. The relays turn ON and then turn OFF after 2 or 3 seconds. Here is my Mega 2560 code. phasex, neurtralx are the relays. #include <avr/interrupt.h> #include <avr/io.h> String inputString; boolean stringComplete = false; int phase1
HI Everyone here. I am currently working on GSM project. i have interfaced GSM900 modem with avr ATmega16 uC on uart pins. using EEPROM to store the NUMBERs of allowed persons. as of now Maximum Three numbers are stored. another string Named SLAVE is used to store slave string received from particular phone number. Each Number and Each SLAVE is ha
change txt to .hex I am using CP210x USB-to-uart Setup
Hello guys, I am facing an issue, where I can't manage to work SPI interface connection between two atmega's. Basically, I am trying to get data from slave avr uart input and send it to master uart pin through SPI. I guess the problem would be somewhere in code (maybe opening SPI connection...). If anyone could take a look and comment (...)
Guys, I tried to compile : #define uart0_RECEIVE_INTERRUPT SIG_uart0_RECV and got : attempt to use poisoned "SIG_uart0_RECV" I'm using avr studio 6.1 any ideas on how to rectify it ? Thanks
yes u can interface with uart protocol......... Refer the link